Recent content by stalker170

  1. S

    Evinrude 1993 150 hp stalling issue.

    I have been dealing with this for a while and cannot find the issue. Motor runs perfect when you start it up, runs great all thru the power ban and at WOT. But after I get to my fishing hole and try to move, the motor stalls when I put it in gear. All I need to do is keep pushing in on the...
  2. S

    1993 150 6 cylinder Intruder (Need your Help to figure this one out)

    I have this motor on a Stratos bass boat. It has been a unbelievable motor. Could not tell you the how many gallons of gas has been put thru this motor. I fish 18 tournaments a year. So, it owes me nothing. Here is my issue: Last fall fishing my last tournament running up lake in the...
  3. S

    1993 150hp V6 Intruder

    I have been having some low end issue with my 150 Evinrude. When ideling, it was spitting and quiting. I put some Evinrude engine turner in the system. The stuff I have is the stuff you inject in thru the tire stem valve by the carbs. I let it set four hours then hooked the muffs on, and it...
  4. S

    Charging Problem

    I have a 1993 Evenrude 150 Intruder. Last night coming into the Landing I noticed my tach was not working and when I looked at my volt meter she was setting on 12 volts. It always runs around 13.5 Volts. Everyone tell me to just order a reg/rec. I will look at all the connections tonight...
  5. S

    Merc 90HP

    I just bought a 1994 Nitro 170 DC. It has a 90hp Merc. The guy that had the boat before me had a 13 1/4 inch, 17 pitch prop on the boat. The boat RPM is way to high. When I trim the boat where it is supose to be, I am in the 6200 RPM range. I did try a 12 inch 23 pitch. It did get better...
  6. S

    1950 Sportfish 06

    Been looking at buying a 2006 Crestliner 1950 Sportfish Outboard with the SST package. Anyone have knowlege of this boat or information?
  7. S

    Low speed jets on a 115hp

    I have a 1992 115 inline 4 cylinder Mariner.<br />I have owned the boat for two years. Ever since I have owned the boat it ran a little bad on low end. I checked the setting on my low speed jets. The book said they should be set at 1 1/2 turns out. Mine was set out 1 3/4 on both carbs.<br...
  8. S

    Neutral Safty Switch

    I have a 1991 Mariner 115 four cylinder.<br />I went to turn the key yesterday while I was fishing to make a move and nothing happened.<br />I turned the key on and jumped it out on the solenoid. It started and I headed for the launch.<br />When I got to the launch I tried it again and it...
  9. S

    Changing stator on Mariner 115

    I have to change my stator on my 1991 inline 4 cylinder Mariner. Is there anything I need to mark before I remove the stator? I cannot mark anything on the inside because the trigger is covering any metal that I can ***** punch. I see the flywheel is on a key, so that can only go one way...
  10. S

    1992 Mariner LOST FIRE

    I was wondering if someone could tell me what color wire to unhook at the motor to see if my kill switch is bad. My motor is a 1992 Mariner 115hp inline four cylinder. Also does anyone know what color wire at the CD box should have voltage present when I turn my key on. I have ordered a manual...
  11. S

    1992 MARINER FIRE PROBLEM

    A year ago I had a 35 hp merc on my small bass boat. The same thing happen to me a year ago. I went out to pre fish for a bass tournament, and I got to my spot, shut the motor down, when I went to starter her back up, I had no fire. I do not remember who helped me on this board, but they...
  12. S

    Max RPMs of Mariner 115 1991

    I had a post a couple weeks ago on a boat that I had just bought. I was asking the question about jackplates and RPMs of my 1991 115hp Mariner. With some help from the board, I was able to do some checking on some things.<br />The boat has four props that came with it. The guy I bought the...
  13. S

    RMPS of 115 Mariner

    I have just bought a ProCraft bass boat with a 115hp Mariner. It has a manual jack plate. In a earlier post I asked the question about the jack plate, And what will happen if I adjust it.<br />My concern is that the motor will run aroung 48 to 50 mph at WOT. She is turning 5600rpm on the...
See more
Top