Here it's only December 10, And I'm already putting My boat away for winter:mad-new:. I most likely won't get it out until March.
It's going to be a long 4 months.:cool:
Stuw
Re: Good Boat names
Re: Good Boat names
I like it! You have a picture of her?
I was not sure which Her You were talking about. Here's a couple of pictures of both of Them.
It's GREAT having a Wife and Mistress that get along. The Mistress is a 1988 Bayliner Capri 19' I met her...
Re: Good Boat names
I like it! You have a picture of her?
I was not sure which Her You were talking about. Here's a couple of pictures of both of Them.
It's GREAT having a Wife and Mistress that get along. The Mistress is a 1988 Bayliner Capri 19' I met her in may 2012 she was being ignored...
Hello Everybody
I want to clean the grime from My Powerhead and cowling it's a 1988 Force 125hp. I'm not sure what to use.
On My Cars & Bikes I've used foaming engine brite.
Is this good to use on My powerhead if I let it dry out well and then lube all linkage and cables before I start it...
Hello All,
This is on a 1988 125 HP model 1251X8A Long Shaft. My Prop Shaft has a slight bend in it about 10 thousands of an inch.
Is this to much to run?. There's no vibration:D.
Can someone verify that the # 4 on the Lower unit by the fill screw means it's from a 125 HP motor, And a # 3...
Hello All
Can Anyone tell Me the difference between a 4 Blade & 3 Blade Prop?
The Boat is a 1988 Bayliner Capri 19' with a 1988 Force 125hp (that I'm very happy with) (surprise surprise).
I don't pull a Tube or Skier I just cruise around and sight see. Hole shot is nice but I'd rather have...
Hi All
I'm looking at Props. on Ebay and I found Two styles. Can anyone tell Me the difference between these Two styles.:confused: One has round Blades and One has flat side on the Blade
Thanks in advance
Stuw Pidasso
I just thought I would not write about any problems or complaints. We took Our boat a 1988 Bayliner 19' Capri Bowrider with a Force 125 hp (Ran strong and smooth tilt & trim work fine) out for a mid day cruise and have Lunch at Park with a dock about 30 Miles away from the ramp by Our house...
Hello All:
Can an aluminum Prop. get repitched from 19 to 17 or 15? I have a 88 Bayliner 19' Capri with a Force 125 with a 13 1/4 X 19 Three blade Prop. Top speed is 35 mph GPS. I would like to have spare Prop that is a 13 1/4 X 19
repitched to 17 or 15.
Any and All Info would be great.
Hi everyone
I put a Tiny Tach on My 1988 force 125. I would like to know how many times the Spark Plug fires per revolution? I have it set to read 1 spark per rev, I just got back from the Lake and the Tach said the Motor was turning over 7100 rpm's at 35 mph checked by GPS. I know thats not...
Your information on trim & tilt repairs is GREAT:D, It got me through My T&T problems. I hope My work is as good as your advice. I'll be on the lake on Monday with the WET MISTRESS :cool:( less crowded & no PWC's) We'll see how good the repair is.
THANKS AGAIN
(stuw pidasso)
Gary Allen
Will a 300-F658095 Stator from 1988 Force 125 hp work on a 1990's Force 120 hp that uses a 300-888793 Stator? I'm trying to save money and use parts that I have instead of buying new.
Thanks in advance
Gary
I'm looking for a Fuel Pump for My 1988 Force 125 HP motor, And would like to know if a 1989 125 HP pump is the same one used on 1988 125 HP?
Thanks
Gary
I have a 1988 force 125 hp serial # 2050 modal # 1251X8A. I'm going to replace My trigger with a remanufactured one but it does not come with a wiring diagram. Can someone Please help Me with a trigger diagram? I orderd a Manual but I don't know when it will get here.
Thanks
Gary
Hello All!
I hope I'm not hijacking this thread.
I'm not only new to this Site , I'm new to Boating. I have a 1988 bayliner Capri 19' bowrider W/ a Force 125, I just put in a new Floor, floor supports & Fiberglassed all of the Wood. From this Site I learned how to set the timing & adjust the...
