Recent content by SumDumGuy

  1. S

    new to me old Evinrude 15hp

    Re: new to me old Evinrude 15hp Here's another question. There is a "plate" and spring on the upper shift rod. When I try and move the rod up and down it hits the yoke of the tilt lock. What is this thing and what is its function? Should the plate be above or below the clamp yoke. Here are...
  2. S

    new to me old Evinrude 15hp

    Re: new to me old Evinrude 15hp couple more...
  3. S

    new to me old Evinrude 15hp

    Hello, I picked up this motor today and need some help confirming the model/year. There is no identification on the motor but I am guessing it is a 1953??? Also, any source for a parts list for this year motor? Anyone know what years parts are compatible? I am thinking the gear box is going...
  4. S

    stripped tiller throttle gear

    I have a tomos 9.9 and the tiller throttle gear is stripped. I am wondering if anyone has any ideas for replacing the gear? Take a look here... It can be seen that when the handle is turned the handle gear rotates and extends/retracts the mating throttle gear (it can also be seen that the...
  5. S

    Tranducer ID and Head Unit

    Hello, I bought a little tin boat and it had this transducer afixed to the transom. I know nothing about these gizmos, so can anyone ID the transducer and the applicable head unit? Thanks!
  6. S

    1954 Clinton Model 25

    The disease I have hit me again yesterday and I had to buy another motor. What I think I ended up with is a 1954 Clinton Model 25 2.5 hp, but I am not positive. Does anyone have any info for these motors, oils, mixes, etc? Also, the tabs in the starter do not engage the cup any longer. It...
  7. S

    Codependence

    Re: Codependence
  8. S

    carb float needle

    Re: carb float needle did it not come with a clip that ensures the needle comes back down? something like...
  9. S

    Opinions on to buy or not to buy 1960 20hp Chrysler

    I saw an ad today stating the following: $100 I have a 1960 out board motor that runs really well just put new plugs in it. comes with a 6 gallon gas tank the isnt the cheap plastic ones its a metal tank. the problem with the motor is its picky on when it wants to go into gear. i dont know if...
  10. S

    1955 Johnson 25hp

    I was looking at the classifieds last night and came across a "20-35hp classic johnson motor from the '50s." The ad further stated that the engine was seized. All this for $60. Since I was looking to get a hold of a 15hp I threw the dice in hopes that it would be 20hp or lower. I was a bit...
  11. S

    Johnson QD 10 hp motor tilt

    I heard there is no such thing as a dumb question, so... I have both a 55 and 60 johnson 10 hp QD motors. For the life of me I cannot figure out how to change the tilt of the motor. I can see the piece that will move to a different slot to change the tilt, but I cannot figure out how to make...
  12. S

    engine position on transom

    Can you tell me what you think about the position of this motor? The plate is about 1.5 inches below the hull. Should I try and bring it up higher? If so, how to bring it up?
  13. S

    Prop value??

    Re: Prop value?? more...
  14. S

    Prop value??

    I picked this prop up the other day and was wondering if it had any value? Also, if it does where is a good place to send it off? It says it is a 14.25x21, it is aluminum and it is also stamped with Mercury. IT appears to be in good condition, no cracks but there is a little bit of blade wear...
  15. S

    Small aluminum boat ID and transom suggestions

    Re: Small aluminum boat ID and transom suggestions transom wood pics...
See more
Top