Would anyone happen to know which switch I would need to order to replace the OEM switch? Looking through the catalog here gets confusing as heck. Couldn't find a part number to cross reference it with, old switch only says "Indak" on the back side with no part numbers.
In dash mount, 3...
Just an FYI for anyone looking to pick up a tinytach on the cheap. Amazon currently has them listed for $18.99 plus shipping.
I believe this is the older model that had a slight delay in the update timing of the tach readout as opposed to the newer "standard model". 2-3 seconds as opposed to...
Looking for any and all info for a 1978 thunderbolt 700. Serial # 4978035
Recently acquired this motor and it's got the classic deteriorated / burnt engine harness issues. Can't seem to find much info on the net about this year/hp. Looking for a way to reference the harness to see if I can get...
I'm trying to figure out if the factory tach from a 1986 bayliner with the volvo/ penta setup will work with my 1986 Bayliner with the Force 125hp.
I picked up a complete dash panel with all the available gauges offered in 86 in working order from a guy who was going to pitch it in the trash a...
Your Welcome. Click no to pro account when pop up opens and then click slow download and wait 1 minute for the file to start downloading.
up to 2006 basic trouble shooting guide:
http://rapidshare.com/files/453372546/2006_troubleshooting_guide.pdf
Chrysler 20-25 hp 1969 - 1976...
I have an 86 force 125hp on a 1986 Bayliner Capri Cuddy.
Prestolite ignition system. 2 CDI units, 4 ign coils.
I'm having a problem with no spark on the #1 plug.
Compression is good. All fuel system components have been cleaned, rebuilt, or replaced and set to specs.. Including the carbs and...
Could someone give me clarification of the timing marks on this motor?
I've included a picture. There are 3 marks close together at what I assume is the 0 degree TDC mark. There is another mark (to the right in the picture) which I assume is the 32/34 degree WOT setting?
Okay are my...
Has anyone used that expanding spray foam insulation called GreatStuff that you can find at the local home store? I was checking it out the other day and it does seem to be almost the same stuff as the foam I just removed from under my flooring. I'm thinking it is, just in an spray can.
Pros...
Does your boat lean to one side while sitting still in the water?
I have an 1986 20ft bayliner cuddy and I've noticed a slight lean to the right.
I had to deal with wet foam undeer the flooring that I mentioned in another thread. Prior to removing the foam, I had a bad lean to the right as that...
Well live and learn, apparently I didn't do a good enough job of checking the foam out entirely when I laid my new floor in and now it ALL has to come out.
So my questions are this:
I have an 1986 20ft Bayliner Capri Cuddy. I've read a lot of the threads on foam around here and all the stuff...
So I get all done with my restoration project. 86 Bayliner Cuddy 20ft. New floor, upholstery, the works , etc. We get to the launch and she's leaning to the right. NOooo!
When I had the floor out I checked the foam and stringers, etc. it all seemed good and dry or it would have been replaced...
I'm looking to convert a 1961 75hp from a long shaft motor to a short shaft motor. Does anyone know if I'll be able to use the shaft from a 35hp for this purpose. I ask because I have access to the shorter shaft from a 35hp. Otherwise I'll have to start looking again. Are the shafts the same or...
I have a decent 1950-51 5hp Johnson motor that i've trying to find a carb rebuild kit for. In addition to that I also need to find where I can get an actual float for the carb since the main problem with the motor is that the float has begun to disintegrate. It still starts and runs good, it's...
I have the opportunity to pick this little gem up for free. My questions is, is it really worth it. It's a 1959, 14ft Holiday Runabout. In the pictures the windshield looks cloudy but that's just morning frost. The windshield is actually in great condition. No stress cracks, etc. Normal interior...
Couldn't find a proper forum to post this in since it could fit in a few.
If your looking for parts for older outboards check this guys site out:
geocities.com/scottmc9hp/index.html
I don't know him or have any affiliations with him, but it looks like he's got a lot of good stuff for older...
