I have a 2.4 litre 200 HP merc and the trim unit is leaking around the ram on top. Is this a hard fix once i get the cylinder off? or is it relativly easy?
I changed my lower unit oil last week. Installed new Omc oil and oring and nylon washer. They old oil was fine. A little black but had alot of hrs on it. After running for 5 hrs i dropped the bottom plug just to check.The new oil was yellow.Not white at all. Sorta custard color. Did not appear...
I have been told that the 1988 1.6 liter 115 hp omc is the same motor as the 140. Is this true? They both have the same specs as far as bore and stroke. They both have the bubble back exhaust. Other than the carbs what is the difference and would it be worth it to upgrade my 115 to a 140?
Pulled the heads on my 115 to replace the water diverters and gaskets.I found 1 head with alot of pitting on the bottom cylinder. It was obviously rebuilt at one time and the head was not replaced. Is it safe to run a pitted head or should i replace it.
LOOKING AT BUYING A BOAT WITH 1988 1.6 SEA DRIVE. RAN IT ON THE HOSE TO HEAR IT RUN.GOOD FLOW FROM WATER SQUIRTER HOSE. ABOUT 30 SECONDS INTO THE RUN I NOTICED THE PORT SIDE CYLINDERS RUNNING MUCH HOTTER THAN THE OTHER. TEMP SHOWED 180.I SHUT IT DOWN. THE OTHER SIDE WAS COOL. WOULD A FAULTY...
I JUST PURCHAED A 1988 1.6 LITRE SEA DRIVE ON A 17 FT PROLINE CENTER CONSOLE. JUST WONFERING IF THERE ARE ANY SPECIAL THINGS I SHOULD BE AWARE OF ON THE SEA DRIVES. I HAVE OWNED SEVERAL OTHER OMC OUTBOARDS OVER THE YRS AND I AM VERY FAMILIAR WITH THOSE OTHER MODELS. THE SEA DRIVE SEEMS TO RUN...
Ok heres the deal. I finally found the firing problem on my 94 sport jet 90 when i replaced the stator. Fired up fine. Now it is not charging the battery. Volt meter reads 12.2 volts with motor off. After running a while with volt meter hooked up and about 4000-5000 rpm on the water no increase...
HAVE A QUICK QUESTION. WHAT IS THE NORMAL COMPRESSION ON A 94 SPORT JET 90 HP. I HAVE READINGS OF <br />#1 120 PSI<br />#2 120 PSI<br />#3 120 PSI<br />IS THAT NORMAL FOR ALL 3.<br />MOTOR HAD 557 HRS AND RUNS GREAT.
I HAVE A 1997 BAYLINER WITH A BLOWN 112 HP EVINRUDE. I AM REPLACING IT WITH A 1989 JOHNSON 110 HP. THE WIRING HARNESSES ARE DIFFERENT. THE 97 112 HAD 4 PUSH TOGETHER DEUTCH CONNECTORS THAT WIRE THE MOTOR TO THE BOAT CONTROLS AND GAUGES. THE 1989 110 HAS THE STANDARD RED PLUG CONNECTOR. THE WIRE...
1987 EVINRUDE 3.6 LITRE. I HAVE BEEN HAVING AN INTERMITTENT SPARK PROBLEM ON THIS MOTOR FOR A WHILE. NOW THE # 7 CYLINDER HAS NO SPARK AT ALL. TRIED SWITCHING THE COIL AND EVEN A NEW COIL ON THAT CYL. STILL NO SPARK. ALL OTHER CYLINDERS HAVE GOOD FIRE. PAK ALSO CHECKED OK. WHERE TO LOOK NOW?
I RECENTLY ACQUIRED A MERC 90 HP INLINE 6. I CANNOT LOCATE ANY NUMBERS TO TELL ME THE YEAR MODEL. THE PREVIOUS OWNER SAYS HE THINKS ITS A MID TO LATE 60S MODEL. IT DOES HAVE A BELT DRIVEN DISTRUBUTOR AND A LARGE SINGLE BROWN COIL PACK. I NEED TO REPLACE THE STARTER AND NEED THE YEAR MODEL. ANY...
I TESTED MY STATOR. I AM SHOWING AN OUTPUT OF APPROX 20-3O VOLTS MAX OUTPUT WHILE SPINNING OVER. IS IT POSSIBLE FOR STATORS TO GO BAD AND PUT OUT THIS VOLTAGE? BOOK SAYS SHOULD BE AROUND 200 VOLTS BETWEEN THE GREEN/WHITE AND WHITE/GREEN WIRES.
