Have an old humminbird fish finder,that reads 28 to 30 ft etc of water when i can see bottom and know is 3-6 ft.I am new to this and have programmed it to where i think it should be.Is it just old and dead or could there be something else i am missing,and need a new one ......
Thanks...
Will try to keep this breif as possible.I bought an 89 skeeter bass boat with Johnson 110 vro late last fall that didn't run worth a crap.It would start and idle on muffs but when i put it in the water the 1st time started fine fine and idled fine but when i tried to throttle it up it would get...
Temperatures here at night hover around upper 20's and low 30's.Just wonder how concerned i should be about getting motor started and checked out so i can get on the water.89 Johnson 110,boat is outside overnight now.There are a number of guys out on the water now ,so just wonder again about...
I have an 89 skeeter bass boat 110 johnson.All electronics are working except bow,stern lights and the front and starboard rear tilt switches for the motor.Put new bulbs in lights still no go.Checked fuse box all are good.Not sure what to do from here,any thoughts would be appreciated.
Thanks...
Does anyone know if the carcoal metallic gray is the standard for all older johnson o\b's or were there different grays?Just want to make sure color is correct.Can't seem to find matching part numbers,but i'm guessing the Tempo marine motor paint metallic charcoal gray is the right one.
Thanks...
I am getting ready to repaint motor.I have checked through some of the older posts on this topic.I know how to do this project,sand, prime etc.My question is is sandpaper what grits to start with and finish.The lower unit is actually not bad,a few minor spots to prep.Motor cover is chipped and...
I was reading a post in one of the other forums about corroded bolt removal.I am replacing old carpet.My dilema is screw removal.Screws that hold down the drivers seat and passeger seat in Skeeter bass boat.At some point someone replaced original screws with just flat slottted screws that were...
I am redoing the carpet in my 89 Skeeter bass boat.Had no real problem with deck areas,and they look pretty good.That being said the compartment lids(7) are a whole different story!I tried the 1st one with a scrap piece of carpet and getting the fit on the top flat part is easy,the hard part is...
I recently bought an 89 Skeeter bass boat 16 ft with 110 Johnson.I have been doing a ton of needed work on it and will be looking to get a new prop for it.I have only looked quick to find some sort of ident # on it but don't seem to find one.I have read alot in this forum about new prop...
I recently bought an 89 skeeter bass boat with 110 Johnson.I am new to o\b motors as compared to old car motors,and have learned quite a bit,greatly due to this site and the help you all have given.I have looked around on line to find a junk motor to buy,would like same as i have but i know...
I recently posted a question about hooking up a fish finder on an 89 skeeter bass boat.Was told to run directly to battery,which i can do,but was wondering if i can just run it to an accessory switch on dash panel.The only accessories i have on boat right now are trolling motor which is run...
Have an 89 skeeter bass boat 110 johnson.Fish finder was wired into starter switch when i got it,,found out the hard way this is a no no,where is the best place to run power for it.
Thanks John..
Have an 89 Skeeter bass boat,110 Johnson.Was repairing wire for fish finder and touched screw next to the one i was undoing and got spark then no power at starter switch,trim or fish finder.Did i burn switch or are there any fuses im missing checked others,batts are good seem to have power every...
Recently bought Skeeter bass boat.Boat had been stored for 2 years and mice got up in the motor and made one heck of a mess.Looking for other deterents to these little(insert swear word),other than moth balls if anyone has any suggestions....
Thanks John...
