I have a Tournament TF1600 that is rated for a 115 horse. I have a 90 horse on it now but would like more power as the 90 horse is under powered. does lake potrol check this close or very often? would like to put a 150 hp on but dont want to get my boat impounded. does any one know a way around...
which tach will work best on my 1989 90 horse e-rude v-4 crossflow??? <br /> http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=4506143040&ssPageName=STRK:MEW <br /><br /><br /> http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=4506484597&ssPageName=STRK:MEWA:IT
I have a 1989 90 horse that i would like to put a bubbleback exhaust on. would it be worth it for a power gain? will i see a noticable diff in power? and can this be done? what do you guys think?
My 90 horse rude will hook up fine while moving in a straight line but if i vere off one way or the other it sounds as if it may be catching air. the cavitation plate is where it should be to the best of my knoledge. what can i do to the boat or prop to stop this? iI am running a 13x19 prop...
looking at a 1977 140 horse that is much older than my 1992 90 horse but i am looking for more power. will this engine give me much more top end than my 90 horse crossflow? would it be worth the price of 600.00 i know the older the engine the power was rated at the power head and newer was rated...
my tach has a black button on the back and has a slot for a flat head screw driver to go in but there is know numbers for me to read what pos it is in.Is that what it is for and how do i set it to pos 6 if there are know numbers?
my tach has a black button on the back and has a slot for a flat head screw driver to go in but there is know numbers for me to read what pos it is in.Is that what it is for and how do i set it to pos 6 if there are know numbers?
ok guys, as you may have read in earlier post,I installed a jack plate on my tournament 1600-TF with my 1992 rude 90 horse and checked my cavitation plate while on plane fully trimmed out,the water is touching the bottom of the plate but not the top. seems as the motor is right in the highth it...
ok, I installed a right hite jack plate to the back of my 1989 tracker Tournament 1600 TF 16 foot fiberglass hull with my 1992 90 horse v-4 cross flow to lower the cavatation plate to about 1" above the bottom of the boat. Now my hole shot is great with my 13x19 prop, but when i am trimmed out...
I set my linkage so that both butter flies are closed and both start to open at the same time. now it will not idle. I wish i had left that part of the rebuild alone but wanted to make sure they were right. in nutral the butter flies were partly open. cant seem to understand what my manual is...
I installed a new water pump kit in my 1992 90 horse rude v-4 crossflow and noticed that there was a small hole in the housing. this hole looks to be made in there from the factory. i turned the prop with the muffs on and the lower unit off and water came out the hole like a straight stream. I...
I have a 1992 90 horse v-4 crossflow with a 13x19 prop. i have been told ro go to a 17 pitch prop. should i go 13x17 or 14x17? does anyone know what size came on this engine from the factory? I have to run my engine way down on the tilt to keep a good bite or it seems to cavitate as i start to...
hi all, i have just taken my 1992 rude 90 horse v-4 crossflow out for the first time today. It seems to be running perfect with no signs of overheat. I was nervous about the t-stat issue as you probably read in earlier post. but all seems good. i had to mount the senders to the head cover as i...
ok, I bought a temp gauge for my 1992 90 horse v-4 crossflow and the kit came with 2 sensors and to sensor monting brackets but only one tan wire to hook to sensor. my question is can i get another wire and hook it to the terminal along with the one it came with? can the 2 sensors be tied...
