I have an 1970 Salem Skiff that has Pulley Steering. I would like to switch it to the cable steering. The engine I have is set up for cable steering so that will not be an issue. There are several place near me that have scrap boats that are selling parts. My question is will the steering cable...
I just purchased a 92 Johnson 40 HP VRO with Tracker Pro Series Controller. I hooked it all up but was getting an steady alarm. But the when I turned the Key the engine would spin. Today I figured out my Alarm issue. The wire harness that should plug into the Oil Pump was plugged into the plug...
I recently purchased a 1992 Johnson 40 HP VRO with a Tracker Pro Series Control. As soon as I attach the battery the buzzer has a constant buzz. I have the oil attached and the main harness. There is plug on the engine for a Tach which is not attached. Also there is a red wire that comes form...
Re: Replacing Impeller on Alpha 1 Gen II
Ok so hopefully this is my last question before I install the impeller. I was looking over the parts again today notices on the larger hole gasket that it has a glue strip on one side. So my question is, The the glue strip go against the Face Plate or...
Re: Replacing Impeller on Alpha 1 Gen II
Ok I took a few snap shots of what I bought and a shot of the section in the directions I'm questioning. The date on the bottom is April 1994. I can scan the sheet tomorrow and attach it here.
I have 2003 SeaRay SRX. The top part of the boat has faded and oxidized in the area that canvas top does not cover. Theres not a lot area, but its in plain site. So what are the best products and procedure to take care of this issue?
I need to replace the impeller on my 2003 Alpha 1 Gen II. There seems to be a good video on the Web on this I just wanted to know if this was correct or if the video is missing some steps, or if things can be done better. I did notice in the video that the person did not use the alignment pins...
I have 2003 SeaRay 176 SRX with 3.0 Merc. The bilge pump as broken, does anyone know how I would go about replacing it. It is directly under the motor. It really tight, not sure if I can reach under there. I can believe that the engine would have to come out to get to it. Please feel free to...
I have an 89 Evinrude 88 spl. I melted the #3 piston on Fourth of July weekend. I went to a few Marinas to see able getting it fixed. All said had to replace the power head, $2000.00 just to start plus any other parts needed but none of them looked at it just talked about it. There is no...
I just blew my 89 Evinrude 88 spl. Was offered a 1988 Johnson 110 installed for $1895.00 plus my old engine. It may have some kind of warrenty not sure. Is this a fare price? If not what should I offer or expect to pay? My boat max HP is 110 so this is not an issue. Thanks for any help.
Was out on the lake to and was running fine then lost power. I have an 89 Evinrude 88 spl. On the the way back to the dock it felt like it wanted to gain the power back. I started to pull the plug wires one at a time to check for stalling. Only on two of the wires would it stall. Its still...
The speedometer stopped working on my 89 Sunbird 170 spl. When I bought the boat last summer I tested it at the marina and it didn't work. They did something and it work a few times after that then stopped. What ways can I test besides for electrial. I thought they used compressed air and...
Hey All,<br /> I have an '89 Evinrude 88spl, and like many others it overheats. At the end of the last season the overheat alarm started going off. I had the impeller and pump replace at the end of the season and wasn't able to test until the other day. After about 5 min the alarm still...
