Our 1998 Evinrude E90TSLECM runs great however we have a persistent problem with warm starts. To begin with the carbs have be gone through and cleaned/inspected 3 times. I installed new kits including removal of knockout plugs. The fuel tank, lines, water separator, bulb, and connector to...
I have a 1998 90HP Evinrude on my skiff that I cannot seem to track down an idle/ starting problem. Model is E90TSLECM. I have removed carbs, soaked overnight, put new kits in them except for the knockout plugs. I am running new gas, have checked the fuel pump to insure no diaphragm...
I have a 1999 200hp SWII and the # 2 & #5 cylinders are not firing. My tach also stopped working. I rebuilt my carbs a couple months ago and all seemed fine when I cranked it after this. Today it cranked and idled fine just would not turn up nor plane the boat. Not real sure what the connection...
Can someone post the Link and Synch procedure for a 1999 Yamaha 200hp SWII as well as the correct backing of carb idle screws. I just replaced the middle carb and did a thorough soaking and cleaning of the other 2 carbs. I backed the idle screws on each carb out 2 turns. The engine cranked right...
I recently put a 1999 200 Yamaha SWII Model #SX200TXRX on my boat and had the carbs cleaned at a local shop to solve a rough idle problem. During this I was told that the middle carb on the engine was not the correct carb. When you look straight at the carbs the throats of the top and bottom...
1999 200hp 2 Stroke SW Series II carbed. Everything seems to be working fine but I have a few questions.
1. I have installed a new key switch and it appears to be doing what it is supposed to do but I was wondering if the buzzer should test buzz when I turn the key switch on? Most all engines I...
I have come across a 1999 200hp SW2. Motor appears to be in really good shape, but the hrs are not known. Cranks and runs in the shop fine. I plan on doing a compression check, going over the T&T system thoroughly, and checking the lube in the lower unit. Are there any other obvious points I...
I have a Mercury 1993 2.5L with a great powerhead but a very poor midsection. I have access to a 2005 Mercury 200 2.5L Optimax with a blown powerhead. Will the powerhead from the 1993 bolt onto the 2005 and will the cowling go on it without any problems?
I have a 3 cylinder 40hp Yamaha that cranks and runs perfect for about 100yds then starts cutting out and will not take the gas. It sound like it is missing and only will run about 1/4 throttle. If you cut it off and crank back up it will run another 100 yds perfect but then start cutting out...
I have a bit of a challenge with the fuel tank access hatch locations. I am rehabbing a Parker 21' SE and have purchased a 42 gallon bait tank/lean post and the location for the back fuel tank inspection port will end up under the bait tank. I see no way of working this out. If I slide the fuel...
I have a 1995 70hp Yamaha T&T, Electric Start. It has a new CDI unit and shift shaft. The water pump has just been changed. Motor runs good but the cover is a little faded from sun. I am going to repower my skiff and want to know what I can get for this engine. I will include the 704...
I have a 1995 Yam 70hp. I am having problems with it being slow to crank at cold and not taking the gas until warmed up. Seems like it is not firing on all cylinders at startup. Once it gets over its slugishness it runs great the rest of time it fires right up and takes gas perfectly, but it...
I need the tilt cylinder end screw for a 50hp-90hp Yamaha. I think any year model will be OK as the haven't changed since 1989. I have a 1995 70hp and cannot find a replacement part without buying the entire piston sub assembly.
