Recent content by yanker

  1. Y

    Need help with Suzuki DT65 cooling sensor problem

    Just getting boat ready for spring fishing and now I having this alarm keep beeping at me. I'm getting strong discharge of water from pilot discharge hole (pee hole on the side). While alarm is on, I can pull water cooling sensor and I see water pouring out. I check the sensor and it seem to...
  2. Y

    Suzuki DT65 prop shaft bearing housing remvl

    Hi everyone... Was wondering if you really needed rotor remover slide shaft and attachment to remove prop shaft bearing housing ?? I've tapped it, but it is not come off. Does anyone gotta good idea for me or just go buy the proper tool for the job. What I'm trying to do is to replace all the...
  3. Y

    Suzuki 93 DT65 lower unit

    I'm trying to pull off lower unit for the first time and it gets stuck after about 1/4 of inch. I did remove clutch shaft nut and separated the clutch shaft from the clutch rod. Did I forget to remove something else, or do I need to ply (force) it to remove it ? All book says is to remove 9...
  4. Y

    Oil leak on upper part of DT65 L/U

    I have suzuki DT65 and getting small amount of oil leak on upper part of lower unit when I tilt the motor. I'm suspecting that drive shaft oil seal must be wornout. Can I pull the the lower unit out and pull the drive shaft bearing housing without pulling all the gears out of lower unit? I'm...
  5. Y

    need help on Clinton K753 lower unit

    I'm having problem pulling the lower unit.. I've got almost everything loose, but something is holding it. I have removed 6 bolts between lower column to the engine and bunch of other stuff. Is there a retainer clip or something that will not let drive shaft go down?. I just wanted to check...
  6. Y

    need help with ID on Suzuki Dt65

    I have Suzuki DT65 and Id number on clamp bracket is 06502-910195 which tells me this is 1989 motor. Original owner bought the boat and motor in 1993. Owners manual was also dated 1993. This motor does not have idle speed adjustment switch which tells me it has to be newer than 1991, because...
  7. Y

    Need help with cold start on Suzuki DT65

    Just started having problem with starting in a morning or when its cold (morning sickness). It cranks but will not start. Having choke on does not help. Once I prime the carb with carb cleaner then it starts on first try, and seems like I'm good rest of the day. My earlier problem with lean...
  8. Y

    Need help on Suzuki DT-65 idle

    Motor has been running real good til yesterday when I was washing it down after having great day of fishing out of Dana Point. Lower unit made a squeek noise and stopped the motor... did it couple times. Sounded like lack of lubrication or bearing problem. Today, I decided to go ahead and...
  9. Y

    ff depth problem

    I have Hummingbird 3D vista and having problem keeping correct depth reading. When I first power up, it works fine then bit later depth goes to 1 or 2 ft. Power it down and up again and it works for awhile. do I have unit problem or transducer problem? Hummingbird says they no longer...
  10. Y

    Impeller replacement

    can someone tell me where I can buy impeller (kit) for a Sea king/Clinton K753 ? part number is 220-136-500 for the impeller in Clinton manual. Since I don't see the water coming out of small hole on back of the column, it must not be working ? I went to www3.sears.com to see if I can find...
  11. Y

    Wards/SeaKing/Clinton

    Need help in ID the year and looking for a manual for this motor. Model K7535106A S/N 1540214 Type# XTV52307A I got this motor from friend and it runs good, but wanted to change the propeller to bit larger one to get better push. Been looking around, but don't seem to find any. Do you know...
See more
Top