Recent content by Zeph

  1. Z

    Bayliner Capri, where all is floatation?

    Hi, I have a 14' Bayliner Capri that I will be doing a floor/transom rebuild. I was thinking, would it be helpful to place a couple of small vents (kinda like floor registers) in the floor for some airflow to help dry things out in the hull? It seems water is gonna get down there one way or...
  2. Z

    Want 67 Starcraft windshield

    HI, any chance someone has or knows of a windshield for a 1967 Starcraft Bahama? It's a 16' Runabout. I know it's a long shot. Thanks guys.
  3. Z

    1970's Clinton Sea King fuel pump parts??

    Hey again, I've got the motor running, very well in fact, however the diaphram fuel pump seems like it may be weak. Any idea where I may be able to get a kit? It's the Air cooled, 2 cycle, 5HP. Thanks again guys.......Zeph
  4. Z

    Fuel fitting question??

    Hi, I have a Clinton Sea King 5HP outboard and a Mercury metal fuel tank that came with it. I do not have the fuel line and fittings, How do I know which fittings I will need? I know they are round receptacles on both ends, but I don't know the type? Thanks much...........Zeph
  5. Z

    Sea King 5HP parts??

    Hi, I just got an old Sea King 5HP, I think it's a "Clinton" Model J500 1106B Serial # 356137. I do not know the year and I do not have a manual for it yet. I don't have spark, the coil has 7000 ohms from the high tension lead to either of the 2 black wires, and less than 1 ohm between...
  6. Z

    1967 evinrude sportfour 60hp prop parts

    Hey guys, still a few months before the water thaws here in the midwest, but, I need to get a couple new "spinners" that hold the shear pin in place for the prop. I am not sure what it's called in boating lingo, and I am not sure where I might find one. Any assistance would be great. Thanks...
  7. Z

    1967 Evinrude 60HP prop "spinner"

    Hi, does anyone know where I can get the plastic "spinner" that goes on the prop shaft to keep the shear pin in place? It is the conical shaped piece held on with a cotter key. Thanks Zeph
  8. Z

    1967 Evinrude Sportfour 60HP timing/low power?

    Hi there, I have a 67 Sportfour 60hp on an old 15' Starcraft runabout. I've been getting bugs worked out this summer, but I still have a problem with sluggish acceleration. I've tried a number of things, but tonight I noticed that when checking the synch. between the towershaft and...
  9. Z

    1967 Evinrude V4 60 HP spark plugs??

    Hi there, I have a 1967 Sportfour 60hp. I noticed that in my engine now, I have J4C plugs. I looked in my manual, and it says to use J4J. I assume the last letter has to do with tempurature rating. Could this plug make the motor run weak? What is the differnce between these plugs? Thanks...
  10. Z

    1967 Evinrude V4 60HP prop??

    Hi there, does anyone happen to know about what prop I should be expecting to run on a 1967 Rude 60HP Sportfour. I tried looking on the iboats prop selector page, but I was coming up with none available. Thanks Zeph
  11. Z

    1967 60 hp sportfour evinrude ?? low power

    Hi there, I have a 1967 60 hp Sportfour Evinrude. I have done quite a bit of work to this engine, seals, new wiring harness etc. to get it on the water. I now have it seemingly running pretty well, however it is extremely doggy in getting going. With my wife and 2 daughters, I have to lean...
  12. Z

    1967 sportfour 60hp lower unit

    Hey there, I have a 67 Sportfour 60hp. Does someone know how to get to the seal on the shift rod in the lower unit? I replaced to seal on the output by the prop, and also the seal on the drive shaft, but I still get milky colored gear lube after being on the water. Thanks..........Zeph
  13. Z

    help to find windshield for 67 15' Starcraft??

    Hey there, any ideas where I might find a complete windshield for a 67 15' Starcraft Bahama run-about? I have found nothing local in the area boat dealer "salvage" yards. Thanks Zeph
  14. Z

    1967 evinrude 60HP prop seal??

    Hi there, I got my seal kit for my 67 Rude Sportfour 60hp. I see that I will need to remove the needle cage bearing on the output of the prop shaft. Is there a good way to do this? The rest seems fairly simple...I hope. Thanks Zeph
  15. Z

    Trying to get right parts for 67 Evin 60 HP

    Hi, I'm trying to get my parts for my motor thorugh Iboats. I have a 1967 Sportfour 60HP Evinrude. I assume what they refer to as "gear case seals" would be the lower unit? I came up with part # 18-2689 for the lower unit seals, and #18-3005 on the impeller. I'm hoping I'm on the right track.
See more
Top