Recent content by zindale

  1. Z

    No tt

    Have a 95 mercury 60hp. T and T missing have installed a cmc tt unit. My question is how do i lock the motor down? Will the thrust rod be enough? Dont see a breakaway if i was to hit something what would give?
  2. Z

    What year 60hp

    Just bought a 60hp mercury/tracker. Serial no.not legable found # on powerhead 0g184570. What year? Also its missing all of tt unit. Would a cmc work in place of factory tt. Thanx.
  3. Z

    Proper speed

    I have a 24 ft aqua patio with 115 hp Johnson 14x13prop. Max speed 2adults 1child 17 mph gps and odometer. 4300 rpm at wot . Seems a little slow to me motor seems to sit comparable to others I've looked at seems to push a lot of water around engine. My question is do I need another prop?
  4. Z

    missing prop

    question about where to start had prop stolin of my new used boat dont now where to start. 1548 excel 2004 nissan 25hp 4 stroke. 10x11? thanx for any help
  5. Z

    fuel press test port?

    another dumb question what is the schrader vave for on my 98 115 for? just curious for press or bleeding
  6. Z

    carb sync question

    hey you guys are great. i have a manual ordered be here in a day or two. question if i open my controls wide open should my carb plates be open fully i have a j115tslecm and my max rpms are only 4700 at 18 mph on 24 ft pontoon. with a 14x13 prop. with tt wont change rpms
  7. Z

    prop question

    i have a 24 ft pontoon with an 98 115 johnson wide open is 4700 rpms at about 18-19 mph is that about right is a new boat to me it has a 14X13 prop on it now. thanx for your help
  8. Z

    98 johnson 115

    howdy all thanks for info. i just recently moved over to johnson from the force comm. was curious on how to choke this engine. it has a omc controls with a flip up for fast idle but didnt see how to choke. and is this a premix or oil injected guess i need a manual first. mod# J115TSLECM. i dont...
  9. Z

    wits end- 89 150

    well make a long story short still fighting same ole cutting out problem i have a couple post out there but i guess they are to long no more responses. i have done all i know to do i have inspected lower unit. rebuiled powerhead,fuel pumps replaced 3 ignition modules, 1 coil,stator and trigger...
  10. Z

    inner crank seals on force 150

    any ideas on how to install inner seals without breaking them while trying to line up guide pins on main bearings. 1989 150 5cyl
  11. Z

    boring cyl. block 150hp

    am in the process of rebuilding the powerhead on my 89 150. going 20 over i have heard to chaffer the ports to keep rings from hanging. is what happened to cause overhaul. is this a good idea? also using wiseco forged pistons. will rings also break with these pistons vs stock?
  12. Z

    engine miss under load

    howdy all thanx in advance for any help. i have a 1989 force 150, on a 19 ft fish/ski boat the problem im having has been since i bought it last year. it misses under a load in water through all rpm ranges, enough that it shakes whole boat. inspected clutch dog npf.shop says it needs overhauled...
  13. Z

    tilt trim assy.

    i have a 89 force 150. trim act bent and leaking where can i find an after market tilt trim assy.<br />seems possibly cheaper to replace whole unit than just that act.
  14. Z

    after market tilt/trim assy

    i have an 89 force 150 and the tilt trim bleeds down quick it has a bent act on tilt. was looking for a more reliable after market unit.
  15. Z

    banging and bouncing

    im new to outboards but here goes. i just purchad a 1989 ski boat with a force 150 the problem is it starts and runs fine. so i took it to the water and away i went runs and pulls its self fine but about 22,000 rpm the whole boat jumps and shakes and through out the whole rpm range about every...
See more
Top