Recent content by zubol

  1. Z

    YAMAHA 75 HP 2 stroke CETO from 2011 - gauges

    Can anyone tell me which gauges will work with my new engine? I bought 6Y8 tacho and fuel but I heard it won't work...
  2. Z

    Yamaha 75 HP CETO from 2011 what pole?

    Hello, Does anybody know the pole for tachometer and which wire should be connected to it? THX
  3. Z

    RPM's again (Force 85 HP 88')

    Hello, I have a short question for you guys. At last I run my tachometer and at WOT it shows 4700 - 4800. (26 - 27 kn) Is it OK? or little bit to low? Thank you very much.... Engine - Force 85HP from 88'
  4. Z

    Force 85 HP 88' - cable

    Hello, I noticed my cable between engine and console has been cut off :facepalm:. It's 10 core cable and I am wondering whether I should buy new cable or try to repair it. Cable goes under the deck and might have a contact with water. If I need new one, can I buy any 10 core cable or I need...
  5. Z

    Force 85HP from '88 - Main fuse blows every 5 sec

    Hello guys, Yesterday I took my RIB for a ride. After 1/2 hour it started to stop working. On the beginning it was just for 2 - 3 sec (behave like a turn off for this time), then it appeared often and often and then lose power (about 3 - 4 min and then died). I was 500m away from the beach...
  6. Z

    Tachometer problems

    Hello guys, I have bought one of this tachometers (http://greatlakesskipper.com/product/56_76_80-boat-gauges-outboard-only-tachs/763-tg-faria-faria-outboard-only-oversized-boat-tachometer.html), connected to my engine (Force 85 HP 88') on 20 pole and unfortunately it does not work... Any idea...
  7. Z

    Throttle & shaft cables

    Hello, I have just changed throttle & shaft cables and cannot set them (connect to the engine). It looks like shaft cable is too long... (cables are the same as previous ones) I can set rear gear but cannot set front. Do you have any tricks & tips when you connect new cables to the engine? My...
  8. Z

    Push or Pull throttle

    Could you please answer me this "simple" question?
  9. Z

    Gearbox oil drain screw

    Hello, I would like to change oil in my gearbox. I am not sure if part 44 (http://www.boats.net/parts/search/Merc2/Force/85%20H.P.%20%281988%29/856X8B/GEAR%20HOUSING/parts.html) is the correct screw to remove old oil. If yes, do you have any tips & tricks how to unscrew it? I tried with allan...
  10. Z

    Force cable to Mercury - adaptor

    Hello, I need your advice. I bought Mercury control box and would like to use it with 33C cables (Teleflex red one). Do you think this stuff will resolve my problem? http://www.marinemegastore.com/product.asp?src=GBASE&pf_id=BUR_451074&jump=32&cat_id=ENGCON001 Thank you for your answers.
  11. Z

    Force and Mercury Control unit

    Hello, Do you know how difficult is to connect Force 85 HP '88 to Mercury Top mount control lever? Thanks.
  12. Z

    Water pressure gauge (Force 85HP from 88')

    Hello, Can I use any water pressure gauge with sender? What size of thread in sender has to be used? Thank you.
  13. Z

    Trim/Tilt problems

    Re: Trim/Tilt problems Could you please show me where it is?
  14. Z

    Trim/Tilt problems

    Hello, Last year I changed o-rings and oil in Trim/Tilt, but unfortunately it does not keep the engine in up position. I mean it stays for a few minutes but very slowly goes down. Any advice? Thank you very much. PS. Force 85 HP 1988.
  15. Z

    Force '88 85 HP battery cable

    Hello, Could you please wah tbattery cables I should use for this engine? I need to change existing ones, but I do not know the parameters. I need them 3m long. Also, can I connect 2 batteries for the engine? Thank you.
See more
Top