Search results

  1. B

    Tohatsu m8 2003 8hp jumps up and down

    The motor ran normally the time before. This time when trying to accelerate above low speed or idle it would buck or jump up and down like the the prop was hitting bottom, yet it wasn't. I had a different motor that needed a new hub, but this seems different. The gear oil is good. Spun prop or...
  2. B

    Hyperenergy parts

    Do I need collars or anything else to put this Motorguide hyper energy back together? I have a part number for the lower cowling. Thanks.
  3. B

    No placard on 1959 blue star 14' boat

    Here in Il an hin is required after 1972. I have a title but no card. Can I use a formula to get the numbers then put on the boat? I have never had one checked before. The Il dnr boat section is very slow. Thanks
  4. B

    identifying M50D part

    This part is mounted on the right side of the motor over a bushing. A link goes from it to the lower shift or throttle cable. The parts list is difficult to figure out. Thanks.
  5. B

    1985 8hp srarter spring broke?

    8rcob evinrude Looks like there dhould be a 90 degree bend to catch the notch in the base. I can try bending it if necessary. The lower right picture is the starter. Thanks
  6. B

    Concrete patio/boat tie up sagging

    My photo wouldn't upload so here goes. This 27 year old slab that hangs out over salt water with no support. It is 17' wide and is cracked 7' back all the way across and will eventually break off Can it be fixed and how? Utube didn't help. Thanks.
  7. B

    Can anyone identify this part for Evinrude E8RCOB 8hp 1985 motor?

    Not sure where this white piece came from. The black one goes in the bottom of the manual starter for comparison. I looked at all the parts diagrams and can't find it. I took off the manual starter, carburetor and manifold cover. It was in my parts box but could have come from something else but...
  8. B

    1985 8hp manifold/carb bolt replacement

    How do these bolts come out? threaded? Pressed in? I used a die to cut what I could but it would be better to put a new one in. Thanks.
  9. B

    Jw-14 compression 60#

    I couldn't find pt 11 62 johnsonon utube about rings. Is there any on subject out there? Will soak with tranny oil although it gets run 4-5x. A year. Thanks
  10. B

    Tohatsu M50D 50hp tilt trim pump

    The motor works but the pump doesn't. Can the pump be repaired? Can it come off separately from the motor? I tried to remove the entire unit with a hand help propane torch with no luck. It has been in salt water. I do have a bigger torch but am concerned about getting it too hot and damaging...
  11. B

    How do m50d drive shaft seals go in?

    The manual I have says both open ends of the seals face outward or towards the bottom when inserting but I don't think that is the way they came out. Who can tell me for sure? Thanks.
  12. B

    Good place to get Tohatsu parts online?

    boats.net has a lot of the parts I need but there were 49 (1) stars and 1 (5) star reviews. Iboats is very limited. Any good ides? Thanks.
  13. B

    Tohatsu M50D slow to pump water

    The water trickles out at idle and only about 1/3 to 1/2 the speed of OMC's. The impeller cup looks like new, but the plate it sits on has a slight hump in it where it covers a small cavity underneith that goes nowhere. Is that normal? I have a new impeller and figured I'd get new gaskets and a...
  14. B

    1985 evinrude 8 hp won't accelerate smoothly

    It's a model E8RCOB and I put a new cam roller on it so it should operate smoothly, but.... it accelerates smoothly till about 3/4 full and then gets rough. When opened a little more, it surges ahead in speed and operates smoothly again. What would cause this? Thanks.
  15. B

    Will 2 cycle oil congeal?

    It looks like old paint in the bottom of the jug. The seller said it was 2 cycle oil and is in a proper container. Thanks.
  16. B

    E30LCDM turns hard

    This '86 30hp motor turns hard without the steering cable hooked up. someone suggested it might be the steering bracket bushings. Does the pilot shaft have to be taken out to do this? Can the lower bushing be taken out by taking the lower mounts brackets off only? Thanks.
  17. B

    E30ELCDm exhaust port water

    On this 30hp 1986 motor the water comes out ok through the pee hole but I am wondering about the amount coming out of the upper exhaust ports (2 holes) At low idle it is only coming out as a little spray or none at all. ( I should feel with my hand next time) When the throttle is bumped up to...
  18. B

    1986 30hp midsection is loose

    E30ELCDM There is about 1/4" of space when pulling back on the lower unit and seems to have too much play. is this normal? Also, is the bolt with slot used for steering tension? thank you.
  19. B

    Steering froze at steering wheel

    The steering wheel attaches to a round aluminum piece that holds the steering cable under the panel. My brother says it is hard to turn or frozen. It works on a 1986 OMC 30hp outboard. Are they fixable? Thanks.
  20. B

    Where did Mark Twain put vin numbers? Need title

    I've got an old double axle trailer and can't find any ID on it. Where should I look.There is no title. Illinois won't do anything for me. Where is the easiest and cheapest place to get one? Thanks.
Top