Search results

  1. B

    loss if power at WOT

    well i finally fixed the problem i have been trying to track down all summer. my engine would surge at idle and die as soon as if gets put in gear after being on the lake for 1-2 hours...threw a brand new power pack on it. pretty happy about that but now another issue came about......when i get...
  2. B

    Why is my tach bouncing all over the place?

    can someone tell me what would cause my rpm gauge to bounce all over the place... sometimes it works fine but most the time is all over the place. this is a 1997 evinrude intruder 150hp. thanks
  3. B

    1997 150hp power pack installation help

    i recieved my new power pack in the mail today. this appears to be a basic bolt on part.. am i right about this????are all these goofy tests really required that the instructions say to do???
  4. B

    1997 150 Evinrude Intruder surging at idle???????????????

    i still trying to troubleshoot an issue i am having with the engine. lets try figuring out why it is surging at idle after being on the lake for an hour or a lil more....i have eliminated all possible issues before the motor(fuel lines, filters) ive also put a brand new fuel pump on also....so...
  5. B

    Spark test...how to crank engine over but i do not want it to start?????

    looking to do a spark test...were i put y key in and turn it over doesnt have the clip connection safety thing to take off as a kill switch....how can i do this without the safety thing at the key...
  6. B

    1997 150 evinrude intruder still having fuel problems! any suggestions?

    well now its starting to get frustrating.. been having an on going problem with this thing...runs well at first but after it warms up and after running for an hour or so it dies when i give it gas and can barely keep it running... it is fine in neutral and only does this while under load...
  7. B

    Pulse Limiter? what and where is it? fuel pump replacement

    I just replaced the vro fuel pump on my evinrude 150 intruder. i swapped these out with ease. ive been reading now about this pulse limiter. should i have done something with it? and can someone tell me exactly where it is located. thanks
  8. B

    VRO conversion to premix question? easy and quick!

    i have read the top secret file on how to do this. i am in the middle of doing this. it says to cut to oil line 1 1/2 inches from the motor and plug it. does it really matter were you cut and plug it? i dont think it would i just want to double check. the lines in the motor are pre formed and id...
  9. B

    1997 Evinrude Intruder 150 carb repair kit info

    well im looking to rebuild my carbs. being that this is a v6 do i need 6 carb kits when i order these?
  10. B

    1997 Evinrude VRO issues? Premix conversion???

    I have a 1997 Evinrude Intruder 150hp. i seem to be having some problem and dont know whats going on. can this motors oil\fuel ratio get out of wack with it being oil injected? seems to be getting an incredible amount of oil or not enough fuel..im hoping to get a carb rebuild kit and clean them...
  11. B

    replacement fuel line help

    i plan on replacing all my line from the tank to the carbs...i understand that all the way to the motor is pretty simple. but from the motor to the pump then the carb im not sure of.. i see the lines in the motor are like formed to fit in the motor. do i have to buy special lines for these ones...
  12. B

    out of water decarb?

    ive been doing a little research on this decarb process. some people say it is not needed to go WOT for decarb... so im wondering if i can decarb at home with muffs on?
  13. B

    1997 evinrude intruder150hp decarb process help!!

    im looking to maybe decarb my motor and make sure everything is clean to possibly fix the issue i am having with my motor...im familiar with atv carb but never tore into a outboard carb...can someone give me some input on what to do and what i need to be carefull of before i do this. thanks
  14. B

    Is this compression worth worrying about?

    my engine has a compression of 100 105 110 115 115 115. should i be concerned with anything??
  15. B

    How to remove fuel tank pickup tube

    im having some issues with my motor starving for fuel.. i want to inspect the pickup tube but i cant get it out...i have everything loose and start to pull the tube out and it stops like there is something attached to the buttom and wont let it come all the way out of the hole...anyone know...
  16. B

    How to get the pickup tube out??

    going to inspect the pickup tube in my gas tank..i got the elbow loose and i can pull the tube out but gets stuck like there is something attached to it and wont come through the hole... can someone tell me whats going on here..thanks
  17. B

    Fuel Primer bulb wont stay hard! please help

    Ive been having some issues with my evinrude intruder 150...seems like the first few hours are ok then it just spits and sputters at low rpms and wants to die....when it is neutral it will idle and rev up just fine may smoke a little but no hesitation...as soon as i put it in gear it wants to...
  18. B

    Steering control problem

    got a 18.5ft stratos bass boat with evinrude 150 intruder... im haveing some issues with my steering. seems to always want to pull one way and turning the other way is super super hard. any thoughts? always wants to turn left by itself and right is very hard to turn. thanks
  19. B

    Help! Oil injection question! 150hp intruder

    i have just purchased a bass boat a few months ago. it seems to be running with a lot of oil being injected. is there a way to adjust the direct inject system? i never really had a problem with it until today other than it just smoked a bit. i went fishing at a lake which is basically an idle...
Top