Search results

  1. S

    Educate me on battery systems and set ups?

    As I mentioned in another post, I’ve been considering adding to 12 V batteries upfront in parallel to run a 12 V trolling motor. Then when I upgrade, I’ll be going with the 24 V troller. So two 12 V batteries in series. I hope I got that right. but last night I read about two batteries in a...
  2. S

    Minn Kota powerdrive trolling motor power socket wiring?

    Hey everyone, I picked up a 50 pound thrust powerdrive that I’d like to put on my boat this week. I don’t have a manual and would like to know how to wire this thing up if anybody could be so kind to offer advice. The plug socket has two red and two black leads. One of each has a blue stripe...
  3. S

    StarCraft super sport question

    I have a question regarding the front storage in the bow section of my 16 foot super sport. Can I assume the sheet metal walls that frame off the storage are structural? I would like to install a pair of deep cycle batteries upfront for a 24v trolling motor. One on each side. I haven’t removed...
  4. S

    2 trolling motors from same battery bank?

    so I’m considering 2 electric trolling motors on my boat. Both 24v. One on transom mount and one bow mount. A little unorthodox maybe, but I’m trying to leave my gross polluting to point A-B and use mostly electrics while fishing, question is, has anyone done the same with both motors on one...
  5. S

    How to find your boat sweet spot for best range

    Is there a general rule of thumb regarding cruising speeds maximum fuel efficiency? For instance, does a boat generally consume less fuel once it is just up on plane or do faster speeds generally equate to better fuel efficiency? Do certain RPMs seem to work better than others? I realize that...
  6. S

    For those Starcraft owners who use kickers - long shaft or mount?

    I picked up one of those mounts to raise and lower a kicker but I don’t know if I want to use it and put more holes through my transom on my Supersport. Looking at my old OMC 10 hp, I *think* it might work as far as shaft length goes,but not sure if there's enough real estate left on the transom...
  7. S

    Kicker motors - 2 or 4 stroke?

    I’m reading that there’s a mixed bag when it comes to kickers. What’s your choice for under 9.9 hp, 2 or 4 stroke for dead slow trolling?
  8. S

    Are smaller motors really much better in fuel consumption?

    If a boat moves slower with the smaller motor, does it not consume the same amount of fuel that a larger motor would travelling the same distance in less time? say comparing a 50hp horse versus a 65hp versus 80hp, all versions with the boat planing at top speed. If each traveled the same...
  9. S

    Best choices for kicker motors?

    I’m searching for a 4-6 hp kicker for my 16’ aluminum boat. My budget is tight so I’m thinking my price range will get me into something from the 80’s. Any clear winners out there and duds to steer clear of? shaft length unimportant (I think) as im planning on using a kicker mount. I have...
  10. S

    Rewiring mercury 650 motor

    At the end of the season I would like to start rewiring a 1975 mercury 650. I had a mechanic told me not to touch it because the wiring needs are very sensitive in regards to both gauge and length. I don’t really understand this, as long as a gauge and length are replaced like for like...
  11. S

    1975 mercury 650 carburator information?

    Does anyone know where I could get some information on the carbs on my motor? I bought a Seloc motor manual which is 90% junk. It covers 4 carbs across varying years and model sizes, but apparently nothing for the 650. I would like to set the high low speed back to factory specs. I know...
  12. S

    No reverse lock after lower unit swap

    Hey all, I had the lower unit swapped on my Merc 650 (1975-76) Now I don’t have reverse lock. Any thoughts? I didn’t do the swap but I can’t afford further bills on this so want to see if I can correct myself if possible.
  13. S

    Mooring cover cleaning?

    My mooring covers are getting grubby and mossy around the edges. I want to wash them with a pressure washer but I’m afraid I might ruin the water resistance. I’m not sure if it is sunbrella material or not. I’d like to get more years out of it if I can. Any thoughts?
  14. S

    Considering repowering my Starcraft SS160

    Hey guys I know I post a lot, but I like boat conversations.... Because my old Merc 650 needs much love, which equates to mucho dollars...mucho dollars that could go into a newer setup. I’m having a mechanic give me an assessment this week on whether it’s solid enough. So if I repower, here’s...
  15. S

    1976 mercury 650 problems

    Hey all, I ran my new to me 1976 Merc 650 tonight for about four hours. I took it out fishing. Did a fair bit of trolling. Did not seem to like the idle very low for long periods of time. Had to use the idle lever to keep the revs up just a wee bit. Anyway, concerning part was when I was...
  16. S

    Homebuilt tilt and trim tutorials or build threads?

    I am wondering if anyone here has built their own tilt and trim units and if there was any build threads or tutorials they could point me to? i think I may have to lower my OB and if I make a jack plate, adding PTT if it isn’t a majorly expensive undertaking would be a great idea
  17. S

    Transom and floor replacement - standard plywood.

    Hi guys, I have to replace th floor and transom on my 1976 starcraft. I have some 3/4” exterior plywood (sheathing) Not PT either. I plan on sealing the exposed transom area with epoxy and varnish, and or paint. The flooring will be covered with either marine grade carpet or marine vinyl...
  18. S

    Poor handling, hard to steer at full speed

    Hey everyone, I just did a test run on a new to me boat. It’s a 1976 StarCraft 16’ superport. at speed, the steering is extremely difficult to turn. Fine at low speed’s but very very difficult at top speed. The motor is a 1976 mercury 650. There seems to be a fair bit of play in the...
  19. S

    Clearance height for drive on trailers?

    I know I have a few posts running here, but I wanted to post this question on its own so it’s not buried in another thread. What is or what would be the minimum ground clearance you would give your prop/skeg if you were setting up a drive on trailer?
  20. S

    Swing away tongues?

    How do you folks feel about swing away tongues? I put one on last year but don’t know if I like it. I’m not fond of the sag it has with weight on it. It doesn’t sag in any great amounts, but I can see it slightly and it doesn’t give me 100% confidence. It’s a Fulton brand. Looks good...
Top