Search results

  1. MNhunter1

    New Journey

  2. MNhunter1

    New Journey

    Had a good trip north with the boys for a little shed hunting and time in the woods. Managed to get the deck pulled and maintained in a solid enough state to use as templates and hauled an enclosed trailer home with pretty much everything aside from the hull. Waiting till she’s home to pull...
  3. MNhunter1

    1974 Starcraft SS16 Restortation

    Lookin’ great FIGMO! Been out of town the past few days and catching up on all the posts. Love how the deck and hatches all turned out and great job with the lighting.
  4. MNhunter1

    Shoestring Starcraft SS160 Resto-mod - let the long slow road begin

    I think I have about 25 each in both 3/16 and 5/32 and never really felt I needed more. Granted, I haven’t needed to do any major repairs, but i think about 20-25 each makes for a adequate supply. They are well worth the investment in my opinion, especially when working alone. I’d put the air...
  5. MNhunter1

    The novice build: 1968 Starcraft SuperSport V-16 "The Boat"

    Welcome! You can to the right place for solid and knowledgeable advice. There are many different groups out there on FB and such, but they are flooded with all sorts of various advice and ideas from those that may be appropriate to some that are outright wrong and/or dangerous. They crew here...
  6. MNhunter1

    1974 Starcraft SS16 Restortation

    Nice work! How much of a gap are you leaving for the Nautolex on the hatches? I'm debating making my own as you have, or just installing some pre-fab flush mount ones like the Tempress or DPI Marine.
  7. MNhunter1

    1963 Starcraft Starmist? replacing floor - HELP

    Not familiar with the Starmist, but the deck/layout looks very similar to the Jetstar, Nova, and smaller Holiday runabouts. Looks like you countersunk the rivets. Not sure if you used 3M5200 when you sank them in, but some skim over the countersinks with the 5200 or MarineTex before laying...
  8. MNhunter1

    1975 StarCraft Mariner build "The Unicorn"

    I fished some ratchet straps through the splashwell drain holes (need to fish it in between the transom skin) and back up to the cross member of the kids swing set. Tighten the straps down until it begins to lift the hull off the trailer and you can raise/lower the height of the stern by...
  9. MNhunter1

    Post a pic of your starcraft!

    Looking back through all these great pictures, I realized I never included mine: 1978 16SS 1972 15ft Nova 1983 MR180
  10. MNhunter1

    Hello all, new here.

    Nice Holiday! I think it needs a taller ladder though... 😁
  11. MNhunter1

    New to me 16ft Starcraft!

    Check out the "joggle stick method" for templating your deck if you run into fitment issues. I used it for the bow casting deck on my 16SS and it worked like a champ.
  12. MNhunter1

    1988 Starcraft Mariner MR 220 V rebuild

    I've only used the grey, never the white. I've always associated the white with glassers and the grey with tin boats:) Personally, I'd stick with the grey.
  13. MNhunter1

    1978 22' V5 Super Sport CC

    Likely converted from the dual consoles with the V5 SS plate. Not sure they ever produced a V5 CC from the factory, but I sure like it. You can see the side console mounting bracket still on the starboard side, but the front deck and console look to be standard Starcraft CC/MR/Mariner...
  14. MNhunter1

    Wanted 1981 Mariner emblem

    Unless you're trying to keep in original, I'd lean towards a vinyl replacement. As jbcurt00 noted, like a needle in a haystack and probably much easier to find some sort of alternative.
  15. MNhunter1

    Opinions on seating arrangement on my newly restored 1976 16’ SS

    My Springfield pedestals were swapped around pretty easily. I had a few different heights depending on if I had my kids or other adults along. The pedestals themselves are pretty cheap.
  16. MNhunter1

    1972 Holiday seat replacement

    I’m in the same boat (haha, see what I did there) looking to redo my seats/cushions. I plan to replace the backers with some new ACX ply, seal with epoxy, and see if I can salvage the vinyl covers to use as a template for new replacements. Likely need to find a local upholstery shop to sew...
  17. MNhunter1

    Opinions on seating arrangement on my newly restored 1976 16’ SS

    Sounds similar to the seating I used on my ‘78 16SS. 4 plug in bases + 1 on the casting deck.
  18. MNhunter1

    1988 Starcraft Mariner MR 220 V rebuild

    Do you know a good tig welder? I’d definitely be adding another skin to the transom, but think I’d bite the bullet and have that seam welded with a little reinforcement. Maybe weld on some pods while your at it. Should offset any additional weight of a 4 stroke if you ever go that direction...
  19. MNhunter1

    New Journey

    Building a little 8’ workbench for the garage and going to top it with a 8’x30” “transom” 😁 Picked up a couple extra sheets of 3/4” ACX AraucoPly so figured I’d get things glued up for the pending transom replacement if I was making up 1-1/2” sheet goods anyhow.
  20. MNhunter1

    New Journey

    Yeah, trying to determine the height from the bottom edge of the actual wood transom to the top of the wings to see if I can get it out of one 4x8 sheet or need to use two. Don’t want to half it and glue it to find out I’m too short. Unfortunately, there’s still 4 hours between me and the boat...
Top