Search results

  1. D

    Frustrated with shift/throttle

    Time to bring the rig to the repair center?
  2. D

    Volvo Penta 5.0FIPNCSCE SLOW mode

    This explains everything PM me, I have all the info you need
  3. D

    Overheating

    With vintage posted by you of roughly 20 years ago I'm assuming alpha gen 2 A few gen 2's that have passed my way have suffered from corrosion at the casted dam aft of the water pump assy between the sea water pickup and exhaust cavity. This is including fresh water operated raw water cooled...
  4. D

    Overheating

    Did you replace the sea water pump/impeller or did someone else? Were the parts installed oem?
  5. D

    Overheating

    What is the condition of the drive? Where the sea water pump is located Corrosion on the gear case housing can cause overheat at certain rpm
  6. D

    procedure to manually flush non-running 4.3 engine?

    Bummer Not to impugn your method but a quick run on freshwater muffs isn't a bad choice for a discerning sterndrive operator prior to launch With as many people pro and con on this forum considering salt water use I'd say you're either 100% fine or it's time to replace the entire...
  7. D

    procedure to manually flush non-running 4.3 engine?

    How does a non running engine with raw water cooling get salt water in the cooling system? Asking for a friend
  8. D

    2010 350 Mag MPI bravo 3 gaurdian mode issue. 5% power

    I have zero experience with techmate. I have diacom and g3 at my disposal both with current updates so I can cover many ecm/pcm controlled units I agree that 5% guardian is critical, often times if the engine runs seemingly normal under said circumstances the issue is corrosion. Would be...
  9. D

    Tow rope to Talon bracket?

    Thank you Your OP seemed as though you may be on the verge of catastrophe. Human life is a treasure many take for granted, especially when considering another they've created. This situation not only confuses me but bothers me at times IMO there is never a good reason to visit your local fire...
  10. D

    AC Mr43T

    Which generation of 454? 454 is a complete different engine from an sbc btw. A 7.4 is light years ahead of forgiveness towards an operator/owner as an sbc
  11. D

    Frustrated with shift/throttle

    Pretty sure isn't definite, you may want to check Reason I asked is some vovlo drives are particular about which gear oil/viscosity is used
  12. D

    New 5.7 issues with old(new) starter

    If the removed/missing paint around the hole is not from you installing/removing the starter I'd be curious of the rebuild Iirc, this is the second machine/rebuild shop you've experienced with this motor? And yes, I'd agree with a helicoil/thread repair based on the photos
  13. D

    Frustrated with shift/throttle

    What type/brand of gear oil is currently in the drive?
  14. D

    Changing remote controls?

    Out of curiosity, what make/model of remote did you install. The one pictured in post #16
  15. D

    Strange engine sound need help

    Haven't scrutinized all the posts in this thread but the broad strokes lead me to think OP needs to replace the sea water impeller, the serpentine belt idler pulley assy, and the serpentine belt That, along with a cleanup of the belt dust/patina on the components will help further pinpoint the...
  16. D

    What is this? PLEASE

    First WAG I have is nothing related to boats, at least in a pragmatic sense Post a picture of the area/bolt circle in question. It'll help
  17. D

    Accurate Horsepower Figures

    Correct prop selection requires patience and time. Plus a few props if you're serious First prop I'd try on your setup is a 19 pitch three blade aluminum. Fairly ubiquitous prop used considering your boat/engine and running gear Adjust accordingly for desired performance As far as horsepower...
  18. D

    Volvo Penta 5.0FIPNCSCE SLOW mode

    The tachometer has a fairly direct connection to the ecm through the coil primary wiring The temprature gauge most likely has no wiring/component association with the ecm
  19. D

    Overheating

    The balls need to be seated in the barbs at rest Shouldn't take much effort to move them off the seats but it's important that they seat with little/no gap
  20. D

    Overheating

    They are not The check balls are allowing too much water past at lower rpm. There's not enough supply to the circ pump due to water exiting the exhaust before the circuit pump hose at the t stat housing Remove the balls, turn them around and re tension the springs. Pretty sure it'll aid in...
Top