Search results

  1. jimmbo

    40hp Dead Top Cylinder

    Just soaking carbs isn't going to get all the Gunk out of the Passages. That is why the OEM Carb Kits come with little Disks and Lead Balls. The matching ones on the Carb, have to be removed to gain Access to where Gum/Varnish/Dirt hide and cause issues.
  2. jimmbo

    Any saving the engine? I’m devastated

    Have Never heard of any Snake Oil named Kroll.
  3. jimmbo

    Anti-Ventilation Plate Height?

    I guess that could be a Motor and Prop for a Sailboat
  4. jimmbo

    Anti-Ventilation Plate Height?

    I will assume you have twin outboards, and the fact that you aren't running a Performance type Prop, in fact the Prop shown isn't either for that engine, or some adapters are missing. No it is not the correct height
  5. jimmbo

    Help with my 2005 f15elhd 4 stroke engine rpms. Not a new engine but new to me. Switched to a 12 degree from 11 degree as i felt rpms were high.

    Were both Props from the Line of Props(manufacturer, Model, both cupped or uncupped), or was one Brand/Model A, and the other Brand/Model X?
  6. jimmbo

    40hp Dead Top Cylinder

    The center Cylinder drew from both Carbs. Created some very odd flow through the carbs, which in 2, 4, and 6 cylinder inlines, had induction draw from 2 cylinders 180 degrees apart. with more or less Equal Pressure Drop. With 2 carbs for 3 cylinders, the flow wasn't as even
  7. jimmbo

    40hp Dead Top Cylinder

    Spraying fuel into carb makes no diff, and disconnecting Sparkplug wire makes no diff, Perhaps the Plug is somehow defective, try swapping them
  8. jimmbo

    40hp Dead Top Cylinder

    "Very little Suction"... Was Fuel getting sprayed back on your Hand when you covered the Carb? Are the Oil Streaks on the Block, along the Crankcase Seam, or coming down from under the Flywheel?
  9. jimmbo

    Prop size and pitch

    If you are only getting 3200rpm at WOT, I don't think there a Prop with a low enough Pitch to to even 5000rpm. 1800rpm shy, means you would need an 8" or 9" Pitch, As mentioned, you need to verify the Tach My 78 90hp with a 17, turning 4800 was getting 38mph. WOT Range 4500-5000 My 84 115hp...
  10. jimmbo

    Motor turning to the left

    I assume your motor is a 4 stroke. If not a model# would be very helpful There should be a Friction Adjustment on the Swivel Bracket #23
  11. jimmbo

    40hp Dead Top Cylinder

    When you put your hand over the top Carb, did you feel any Suction? A bad Intake Manifold to Block Gasket can prevent Crankcase Inhalation/Compression, as can a bad/worn Upper Crankshaft Seal. Look on the outside of the Block. Is there any signs of Oil running down the Outside?
  12. jimmbo

    Any saving the engine? I’m devastated

    It wouldn't hurt if you unscrewed them, cleaned the area, hit them with some Deox. Of course there is the risk of Damaging the Wire and/or Connector Ends... The Motor is a 74 and thus 50 yrs old
  13. jimmbo

    What do these 2 rubber hoses go to?

    Maybe a Previous Owner needed an Extremely Stealthy Motor and the Idle Relief was giving him/her away... I have seen many Motors butchered over the Years, and can count on less than One Hand, an actual Improvement over Stock.
  14. jimmbo

    Any saving the engine? I’m devastated

    I guess if the OP is willing to buy a Starter in a yr or so, and looks forward to having to Rope Start the Motor, or Paddle home, he doesn't Need to take it apart, clean and lube it
  15. jimmbo

    Any saving the engine? I’m devastated

    The questioning about it running when it got wet, is because engines that are running can suffer very serious damage, as Water is not Compressible, and if enough were to get into the Cylinder, the Engine would literally stop Instantly, even at 5000 Rpm. Bent/Broken Con Rods, Crankshafts, Pistons...
  16. jimmbo

    4.3 Carb…What’s That Hose?

    You will likely find that the other end of that hose goes to the Fuel Pump, and is there to prevent any Fuel from a leaking Pump Diaphragm, spilling into the Bilge, by diverting it to the Carb. By now the Hose is likely stiff and inflexible, and should be replaced. Again, getting the Hose from...
  17. jimmbo

    Any saving the engine? I’m devastated

    Great to hear Did any water drain from the Carb Bowls, or spray out the Spark Plug Holes? You have to run it for quite a while, to make sure all the Water has either been thrown out of the Bearings, or has evaporated. The Lower Crank Shaft Bearing is the most Vulnerable as the Water can't drop...
  18. jimmbo

    Any saving the engine? I’m devastated

    And keep it running for at least an hour Spraying some Engine Cleaner(BRP) or PowerTune(Merc) into the Carbs when running, will help flush out Water from the Bearings,
  19. jimmbo

    Any saving the engine? I’m devastated

    #36 is the Drain Screw of the Carb Bowl
  20. jimmbo

    1977 merc 150 outboard bogs at WOT

    To get the revs up to 5800, a 17" is likely the Pitch that is going to be needed. The 150 runs great from 4000 to 5800, but below 4000, it can be an unhappy camper.
Top