Search results

  1. tg3690

    max Horsepower rating

    Hate to admit it, but until I read this thread I had never even thought about getting liability coverage for my old bass boat. I have insurance on everything else I own, except the boat. Pretty sure my Auto policy covers it while towing, but need to verify that too. I will be calling my agent...
  2. tg3690

    1992 Force 70 horse rebuild

    ^^^X2....Nice work. It may not be the ideal engine to rebuild, but if it works for you, that is all that matters. (y)
  3. tg3690

    It's 2020

    And don’t forget the scourge of all inland boaters......HYDRILLA....also during the 70’s.
  4. tg3690

    It's 2020

    THE HORROR. Lol
  5. tg3690

    It's 2020

    Reminds me of the Africanized "Killer Bees" that were going to wipe out Texas and the southern states during the 70's. Even made several movies about it. Lol
  6. tg3690

    It's 2020

    Dang! Looks like a little overkill for one hornet's nest. Lol I count like 10 people in full protective gear!
  7. tg3690

    overheating - looking for a cause

    Check back here EARLY in the morning.....JerryJerry will probably chime in with more info.
  8. tg3690

    overheating - looking for a cause

    That flat rectangular plate is the exhaust port cover. Look for a small oval shaped cover near the bottom left corner of that cover that has 2 small bolts holding it on. If you have one, the poppet or "relief" valve is inside. It only works at high rpm's for pressure relief, so don't think it...
  9. tg3690

    1986 35hp Force lower unit.

    Well something must have happened during the forum changeover.....that link for adding a tell tale takes you to a thread about Rosie O'donnel! Lol You could do a forum search instead for "adding tell tale". Looks like a few of those links are screwed up!
  10. tg3690

    1986 35hp Force lower unit.

    Check the "stickies" at the top of this forum. The one for "Force and Chrysler FAQ" click on it.....there is a thread for adding a tell tale "pisser"
  11. tg3690

    T&T leakdown tests

    Thanks for that Nordin.....I have done several comp checks and each time I put the hose/muffs on just in case because I wasn't sure. The manual didn't say anything about it so was wandering how the experts on here do it. (y)
  12. tg3690

    T&T leakdown tests

    Thanks.....stupid question.....whenever cranking the motor for timing or comp checks....you should have water going to the impeller, right? Even though you are not trying to start it?
  13. tg3690

    T&T leakdown tests

    Thanks Jerry....gonna hijack my own thread here and ask you about your 3-wire octopus you talked about yesterday.....what gauge wire did you use? And did you use any kind of connector to plug the wires into the spark plug boots? Or did you just strip the insulation off the ends and cram the...
  14. tg3690

    T&T leakdown tests

    :ROFLMAO::ROFLMAO:Good one! Lol I liked the old emojis better too.
  15. tg3690

    T&T leakdown tests

    Gonna install the new ones and hopefully never have to mess with it again. (y)
  16. tg3690

    T&T leakdown tests

    The new bolts arrived today and will be installing them maybe tomorrow. Had considered just buying some from the hardware store that would fit, but would they be of the same strength as the originals? No way to know for sure so spent a little more and got the ones designed for this...
  17. tg3690

    T&T leakdown tests

    " and a dab of anti-seize on the treads would suffice no??" I will be doing that for sure. (y)
  18. tg3690

    T&T leakdown tests

    I agree with you, the bolts don't look bad at all. And the torque value is only 95 inch lbs or 7.91 ft lbs according to my Chrysler manual. There are 2 reasons I ordered new bolts....the first is I figured some of them would break or get damaged taking them out. Second, I read a LOT of old...
  19. tg3690

    T&T leakdown tests

    I really do feel lucky. After reading all the posts about the bolts snapping off and having to drill them out I was kinda worried about that. The one rust spot.....didn't see any signs of water or moisture in there when I opened it. Could have been like that for many years. Who knows.
  20. tg3690

    T&T leakdown tests

    Never really noticed it before, but after taking the trim cylinder apart I realized it is shaped just like the Chrysler Pentastar logo! LOL. Just a little Chrysler outboard trivia......
Top