Search results

  1. Scott06

    Popped through the intake.

    This is odd - is the top of the coil cracked? Only things I could think of is its coming out of the coil top, the wiring harness is too close and its jumping from HT wire, or you dont have a great cap to rotor connection and the spark has no where to go- only time I saw this was disconnected by...
  2. Scott06

    Is this a trim ram issue? Popping and grinding noises from stern drive. pics and video attached!

    Grease the hinge pins. The two nipples on the gimbal ring by trim sender and limit.
  3. Scott06

    Popped through the intake.

    Replace the wire from coil to cap the archng is loosing spark
  4. Scott06

    Turning point hustler 4 blade

    Have you tried any of the volvo penta props ? have two friends with boats with 4.3s ( one 2 bbl other MPI) and both impressed me with the performance of the stock VP SS prop on them- these are just SX drives not DP...
  5. Scott06

    Ford 302 5.0 H.0. Carburetor omc Cobra stern drive outboard best prop

    yes if you want to improve planning performance yes drop in pitch. How does your current WOT rpm compare to what the engine is rated for? Is the engine in a good state of tune ?
  6. Scott06

    Random overheat alarm 1998 Mercruiser 5.7

    @Scott Danforth may have some ideas.
  7. Scott06

    First time pulling an engine questions

    yes it takes about an hour if you are reasonably familiar. yes you can weld a patch over the rust hole. just completely check it out as you may have small pitting and not worth messing with it.
  8. Scott06

    Height of SeaRay 185 Sport on trailer

    make sure the tower folds down
  9. Scott06

    Parts for 1987 Sportsman Blue Fin 1900 I/O.

    Windshields are tough for boats. There are some guys who part out boats and list on ebay these guys seem to be a boat wrecking yard https://www.laniermarine.com/default.asp?page=xAllInventory places like overtons have seats helm items You may find its not worth the money as by the time you...
  10. Scott06

    Is Vessel View worth it?

    disconnect engine temp alarm switch, oil pressure alarm switch, and drive lube bottle switch test to see if it goes away. If it does reconnect one by one to see which switch is tripping it
  11. Scott06

    Problem Restarting, Idling and Acceleration when the engine is warm. Merc 140hp 3.0 Alpha 1 Gen 1.

    probably a rabbit hole. Figure out why your hot restart issue is occurring - no spark, no fuel or too much fuel. Do you get black exhaust momentarily when it does restart?
  12. Scott06

    Wideband O2 sensor install

    that's barely a bar tab in this sport.... You can use grade 5 as thats is what barr supplied me with their manifolds and elbows if you are fat at idle and mix screws do nothing would suspect your bowl level is too high or one of the floats/needle and seat is getting overcome. I wouldn't expect...
  13. Scott06

    Wideband O2 sensor install

    Mike nice write up interested to see the results. The 7" bolts are availble from mcmaster carr pk of 5 $16 plus shipping but they need cutting a hair too The cup holder in my helm worked nicely for a temporary mounting..
  14. Scott06

    Ol' Girl will not start now a'pre-sinking !?!😩('92 merc 5.7 alpha 1 gen 1 4bbl Quadrajet)!?! HELP!!!

    You can always easily dump a little gas down the carb to quickly confirm it is lack of gas. If there is decent spark it will run a little bit with some gas dumped down the carb.
  15. Scott06

    Problem Restarting, Idling and Acceleration when the engine is warm. Merc 140hp 3.0 Alpha 1 Gen 1.

    Yeah most likely the fuel in bowl is dribbling into manifold after shutdown and flooding it. If the choke closes and gets set this only makes it worse. You need to open the throttle wide to clear the overly rich condition. two safety related comments- is the fuel pump marine rated? Marine...
  16. Scott06

    Inner cable for Mercruiser 4.3L shift cable will not go all the way in

    double check your shift cable routing that's what gave me a similar issue - this is in manual 14
  17. Scott06

    Gimble Bearing

    Most likely previous bearing was worn out and someone kept running it until it spun damaging the aluminum housing. Or the replacement bearing is of lower quality and the tolerance ring is not the right dimension Might be worth trying a different supplier bearing
  18. Scott06

    Lowering the bunks . . .

    Had the same problem last fall when I was taking my boat out pads had rusted stuck to the rotors was able to jack it up put a screwdriver in to retract the pads and then spin the wheels Looks like the metallic in the pads rusted to rotors… sanded the rusty spot on the rotors down once the...
  19. Scott06

    Some possible water in my outdrive and the outdrive was making that clacking noise again. Pics and Videos Enclosed.

    Unless the upper bearings are bad ( cant tell from pics) which would wear is lube was low, willing to bet the internittent my thought as well
  20. Scott06

    Inner cable for Mercruiser 4.3L shift cable will not go all the way in

    You likely routed the shift cable wrong around the flywheel cover and wye pipe. Or at least that is what happened when I did my bellows and shift cable last year... if you look in manual 14 it shows the routing... Are these OEM cables or aftermarket
Top