Search results

  1. Lou C

    Volvo Penta 3.0 GLP-D (PCV valve popping off while running - carbon buildup on boat thru exhaust)

    http://www.volvopentastore.com/Cylinder-Head/dm/cart_id.566785989--session_id.313851465--store_id.366--view_id.786237 I looked up the OP's model in the Volvo catalog and guess what I found... part #13, valve, crancase ventilation.
  2. Lou C

    Time for a ‘new’ boat?

    Hello Ted, What was the engine misfortune? I must have missed it... Anyway I found it interesting that you will stick with the I/O, there are some advantages but the main thing that would stop me (smaller boats) is bad access and cat converter exhaust. The complexity now in inboards has caused...
  3. Lou C

    Volvo Penta 3.0 GLP-D (PCV valve popping off while running - carbon buildup on boat thru exhaust)

    If there is an actual PVC valve in the valve cover instead of just a hose leading to the flame arrestor to take care of blow by, yes if the valve gets stuck blow by building up in the valve cover has to escape and can blow it out if there is a lot of blow by. That Holley carb does have the...
  4. Lou C

    5.7l mercruiser gen 1 alpha 1 to vortec head swap problem please help...

    The QJet I have on mine is the original carb this engine came with and when I replaced the heads 4 years ago I stuck with the pre Vortec heads so I didn’t have to change the jetting in the carb which is pretty close to ideal judging by how the plugs look (light brown). I agree with signing up at...
  5. Lou C

    Volvo Penta 3.0 GLP-D Choke/Starting Issue?

    remember it needs to be grounded too.
  6. Lou C

    How to tel if boat will over heat in the water

    If its the same as the Cobras that housing has a rubber ring inside to hold the 'stat in the housing. Might want to replace that ring too if it hasn't been done in a long time. The standard stat was a 160* unit.
  7. Lou C

    How to tel if boat will over heat in the water

    Agreed water test is the only way. Try to do it early in the AM when no one is around, let it idle to warm up and see what it does. Perferably till the thermostat opens, you may have to run it above idle a bit (1200-1500 rpm) to get it up to temp. Just make sure the water is deep enough to fully...
  8. Lou C

    7.4GL temp sender info needed

    I think these engines used a 140* thermostat vs other Volvo engines that used a 160* stat. I actually tried this same stat in my OMC because the lower temp stat is better for raw water use in salt water. And it does show on the gauge approx 120* at idle. At higher speeds it rises as expected to...
  9. Lou C

    Burned valve or worse 1997 5.7 LX

    I thought the exact same thing, what a nice installation. One day my engine room will look like that lol.
  10. Lou C

    Impeller challenged...?

    If you are careful you can measure that with a ruler and a small T square. I do have all the tools though. One other thing I did, was mark on the cable where it goes into the jacket, where neutral is with a sharpie. Then have someone spin the prop (engine off KEYS OUT) while I shift it into FWD...
  11. Lou C

    1987 4.3 OMC Alternator with 1 Wire Issue

    When I replaced mine I used an ARCO with the B+ terminal and Excite and Sense terminals, the hook up was easy and it has always worked well.
  12. Lou C

    Bow riders with best engine access?

    Glad to hear that Cobalt does a good job in their design!
  13. Lou C

    Bow riders with best engine access?

    beautiful boat! and yes the bigger it is, the more room around the same size engine in most cases. so tell me can you actually reach the starter? and how do you feel about the $5000+ price tag for the cat converter exhaust replacement? If in fresh water its a non issue but here in the salt, I...
  14. Lou C

    Bow riders with best engine access?

    I have see a few that have good access but its usually the larger boats that do, large bow riders, cuddies etc. You don't want the ones with the build in 'glass around the rear jump seats, or the fancy swim pad with the walk through or the flip seats that make the engine compartment 2/3rds the...
  15. Lou C

    High oil pressure smell of gas in oil

    And if you are using an advance timing light when setting base timing make sure the dial is on ZERO...this tricked me a few times....lol.... PS take a look at the center electrode porcelain on your spark plugs, the depoits on this will tell you if its running out of fuel (probably blistered...
  16. Lou C

    Exhaust Manifold Replacement

    Nope 100% salt water here in Long Island NY. Kept on a salt water mooring for approx 6 month season each year. In that pic I had just installed reman heads and new exhaust so everything was freshly painted.
  17. Lou C

    Impeller challenged...?

    The final adjustment should be done with the drive off using the OMC alignment tools, yep. First though you really should check the shift rod height in the lower unit. Next, the tool that holds the bellcrank at the 90* angle to the pivot housing goes on first then you use the shift cable tool...
  18. Lou C

    Exhaust Manifold Replacement

    if you want, take a new bolt for the manifolds to a hardware store, and have them match up the thread pitch, to 2 longer bolts. Get the 2 bolts, cut the heads off and cut a slot in the stub that's left. Then thread these in the first and last holes, slide on your gasket, manifold and install the...
  19. Lou C

    High oil pressure smell of gas in oil

    The other thing that can cause high oil pressure is water in the oil. If you’re not seeing it on the dipstick look inside the valve cover
  20. Lou C

    Engine rpm is not stable below 2000 rpm

    thanks for posting this up, I am a loyal Quadrajet fan but if something happens to this one there really aren't a lot of good cores left so being able to use the easily found 1409 is a nice option. I tried the Holley that OMC and Volvo used in place of the Q-Jet and it never ran right so I took...
Top