Search results

  1. R

    2000 70hp Johnson semi start/ won’t stay running

    Test the overheat horn.---Install new impeller.
  2. R

    Water pump issues

    If testing in a bucket the water must be 6" above the impeller.
  3. R

    Boat not planing

    Sounds like the 25 HP has issues.----Running on 1 cylinder ?
  4. R

    I think I will go electric for my next new car ...

    Electric vehicles are expensive to own.----I saw an article where an owner was quoted $16,000 to repair an antifreeze leak.-----They write them off if there is any sign of battery damage,--- Insurance company can not risk a damaged battery on a vehicle.----That is because cost of a fire caused...
  5. R

    Outboard top cylinder getting hot

    A factory manual is best.----Some other manuals belong in the wee house with the 1/4 moon in the door.
  6. R

    2000 70hp Johnson semi start/ won’t stay running

    Some will argue.----But if a motor has sat for 13 years it needs a new impeller.
  7. R

    2000 70hp Johnson semi start/ won’t stay running

    I don't think plastic carburetors were ever used on the 3 cylinder 70 models.
  8. R

    Help with my outboard!

    I doubt there is a head gasket on that motor.
  9. R

    97 Force 120- Low idle at times, stalls when engaging into gear

    You need to do the compression test.----Checking the 3/8" gap has nothing to do with the sparkplugs.-----You use a device , bought or homemade to test spark !------Good luck with the motor.----Perhaps find a friend to help you.
  10. R

    2000 70hp Johnson semi start/ won’t stay running

    Did you make sure that the high speed jets ( orifice plugs ) are clean ?---They are found way inside the carburetor bowls.----Often over looked.
  11. R

    Complete removal of vro components

    It is not common to get rid of all those pieces.----I am going to look into getting rid of it on a 150 HP with 2 older 100 HP pumps,----Can't say how yet and not going to explain here how it is done for safety reasons.-----Your local dealer might help you.
  12. R

    2000 70hp Johnson semi start/ won’t stay running

    You have to wonder why it sat all those years.----Post compression values.
  13. R

    97 Force 120- Low idle at times, stalls when engaging into gear

    Nobody here can put hands on your motor.---Check head bolt torque.-----Have you adjusted low speed mixture screws ?----Information must be posted.-----Post the compression values.----Does spark jump a gap of 3/8" on all 4 leads.
  14. R

    Which bearing kits do you guys prefer?

    Most towns have / used to have an industrial bearing supply store.
  15. R

    Which bearing kits do you guys prefer?

    I went to a bearing supplier.-----Clearly stated that I wanted quality bearings.----Not a kit from the " hueflungdung " distributor.----No need to save $15 / $20 at all.
  16. R

    03 mercury 60hp hard start, blue smoke

    Are you pushing the key in and holding it in while cranking to start it ?
  17. R

    Low compression on Johnson 45hp pull start.

    It should be easy to determine once head is off.----Post picture of top cylinder.
  18. R

    Complete removal of vro components

    I would say ---Yes it can be done.------Will need a 0438559 pump.
  19. R

    Low compression on Johnson 45hp pull start.

    As clearly stated the head can be removed with powerhead in place !
  20. R

    Low compression on Johnson 45hp pull start.

    Pull the head off now.-----The head can be removed with powerhead left in place.----The head is warped and needs to be resurfaced before new gasket is installed.---
Top