Search results

  1. J

    Replacing Motor mounts

    I’m trying to get YouTube to load this video. Went out and recorded the motor mounts on my outboard being replaced: they were completely shot. Ed the guy that works on them did exactly what flying Scott posted above.
  2. J

    Replacing Motor mounts

    Yes I am Hoosier. That there is fantastic! I bet I would absolutely fly in my v hull, or just get stuck immediately…
  3. J

    Replacing Motor mounts

    these were the best videos I found. Can’t say any of them were overly helpful after watching them a few times through. Motor mount replacement be an outstanding video for someone to make
  4. J

    Replacing Motor mounts

    Gentleman I know that had been working on these motors for many years said $160 labor to replace them. I’d say money well spent.
  5. J

    Replacing Motor mounts

  6. J

    Replacing Motor mounts

  7. J

    Replacing Motor mounts

    Outboard in question is 1980 35 hp tiller.
  8. J

    Replacing Motor mounts

    I was able to successfully replace the lower motor mount. I found a good video to help replace the hard one in the middle below the powerhead.. The one two on the side of the lower cowling I am not quite sure how to replace. Anyone have a link to a video?
  9. J

    Trailer bearing blowout. Need help with repair(s)

    I not far behind you at all in this department. I check my tires and bearing before EVERY trip. My boat ramp is about 10 minute drive and I don't even want to have any problems that close to the house. I will venture about an hour away at the most. I have a small son that goes out with me often...
  10. J

    Trailer bearing blowout. Need help with repair(s)

    yikes! my greatest fear on the road coming true. I stay so paranoid about my bearings and tires its way overkill. Glad no one is hurt. The $360 seems like a cheap lesson to learn.
  11. J

    Lengthening a boat trailer

    We did this to mine recently and its worked out great so far. I have a little 16 foot tin boat though, so weight isn't very heavy (1000 trailer and all i think).
  12. J

    Going rate on a good running 15hp?

    My neck of the woods (Indy) Id say around 650-800 is average for a running motor. One with a warranty from the "motor guy" in town is about 1200.
  13. J

    Strange boat disease strikes.

    I was actually talking to a guy at the marina recently about this exact same thing. Lots of boats from 2000 and before seems to be rotting out. He said he thinks it has to do with increased corrosive components in the air. Like too much pollution or moisture or something similar not mixing well...
  14. J

    1990 Evinrude 9.9/15 still starting rough

    Went fishing last night motor started in about 3 seconds and ran just fine. Ill take it out a couple times this week and see what happens.
  15. J

    1990 Evinrude 9.9/15 still starting rough

    Came home from work to do another cold test. Still hard to cold start motor. I am going to start looking for a leak of sorts. I think that’s probably the next issue.
  16. J

    1990 Evinrude 9.9/15 still starting rough

    Yes. I did some garage starts last night and seemed to work. I had the rom around 850-900 which is good idle a little too slow for the initial start (atleast with this particular motor). No ability to turn throttle handle at all made me stuck at 1 option for rpm in neutral, either 1 lower rpm...
  17. J

    1990 Evinrude 9.9/15 still starting rough

    Got it! (Atleast I think) simple enough fix. I didn’t realize that knob on tiller handle next to kill button could be adjusted: mine was tightened down all the way not allowing me to manipulate Rpm in neutral. I can get higher rpm to start and throttle down for idle speed:
  18. J

    1990 Evinrude 9.9/15 still starting rough

    I ordered a new part and replaced it since it was missing originally,
  19. J

    1990 Evinrude 9.9/15 still starting rough

    read through a bunch of the leeroy rambling website. Tons of great and useful information to try!
  20. J

    1990 Evinrude 9.9/15 still starting rough

    Thanks for the suggestion! I sometimes forget about his page. I will try turning my idle speed out and see how it goes. I do have that motor set to such a low idle i can see that being a problem.
Top