Search results

  1. JASinIL2006

    Advice on first extended trip with 14 footer/7.5

    This.
  2. JASinIL2006

    Possible Business

    I don't know where you're located, but in my area, there are not a lot of options for getting boat motors repaired, outboards or otherwise. I've been to a few of the places in our area and I was not impressed with the quality of the work. I'd love to find somebody like you, if you did good work...
  3. JASinIL2006

    New to boating, first restoration

    Sorry to say, but knocking on things will tell you nothing. You really need to drill test holes and inspect the shavings for moisture or rot.
  4. JASinIL2006

    Restoring a 1990 Larson

    Getting to stand on a solid deck is a milestone! It also make subsequent work a lot easier! It's great to see this boat coming together!
  5. JASinIL2006

    Larson SEI 180 Complete Rebuild

    That's some nice work! Your boat looks brand new... better than new, actually! It is clear how much work you put into it. Well done!
  6. JASinIL2006

    Advice on first extended trip with 14 footer/7.5

    We have a place on a small lake up in Ontario, more east of Sault Ste. Marie than north. Our cabin is on the opposite side of the lake from the road/parking area, so every year, we have to lug our stuff a mile or so across the lake in a boat almost the same as yours. When I first started going...
  7. JASinIL2006

    Fibreglass boat floor replacement - do I need to use fiberglass?

    I didn’t find plugging the foam pour-in holes and relief holes to bo all that arduous. frankly, the idea of trying to shave off the foam after pouring it at the perfect level so the deck will sit correctly sounds like much more of a pain in the butt.
  8. JASinIL2006

    Starting Mercruiser 350HP In/Out Board Engine after 4 years

    Ok, just worried the engine wasn’t drained. Lowering the outdrive and letting it sit would not get the water out of the engine block; only pulling the drain plugs would accomplish that. yes the engine was drained before it was stored, that should be no problem.
  9. JASinIL2006

    Starting Mercruiser 350HP In/Out Board Engine after 4 years

    Did you drain the water from the engine after the boat was last used? If not, you might have bigger problems, like a cracked engine block.
  10. JASinIL2006

    1987 Larson DC-215 restoration

    Famous last words! Seriously, though, it's looking good. You're getting close!
  11. JASinIL2006

    Alpha1 Gen 2 Gimbal Bearing

    A lot of members here who are really good at keeping up with maintenance like the greasable gimbal bearings. However, I have not heard of many problem with the sealed bearings. (Sealed bearings are used in all kinds of vehicles, so they're nothing new.) Personally, I'd go OEM.
  12. JASinIL2006

    Engine Bay Rebuild - Motor Mount Blocks??

    My boat was repowered before I bought it, and whoever put in the engine (a 350 Mag replacing a 4.3), used shims under the front motor mounts. When I restored my boat, I didn't need to remove or rebuild those mounts, so I kept the shims. (I think the shims may be Starboard, but I'm not entirely...
  13. JASinIL2006

    Help identifying a boat that I picked up.

    If you use wood and just properly store and maintain your boat, you can save a ton of money over using Coosa. Much of the problem with wood boats is how they're made and cared for; you can remedy both by building it better than it came from the factory, and by taking care of it to minimize...
  14. JASinIL2006

    Restoring a 1990 Larson

    The grinding was the worst part for me. Hope you get to the rebuilding part soon; that's when it gets fun!
  15. JASinIL2006

    new transom cutout alpha one

    I used a holesaw, but that really only works if you cut that part first. If you’ve already made the rest of the cut out, there is nothing for the holesaw to grab into.
  16. JASinIL2006

    Tongue weight, single axle vs tandem

    On a number of F150 forums I visit, they will tell you the 10% rule for tomgue weights isn’t necessary due to a boat’s wind-slicing profile. Concensus there is 6-8% tongue weight for most boats. 10-15% is for flat-front travel trailers and such.
  17. JASinIL2006

    Buying a boat with a rebuilt sterndrive??

    A rebuilt motor wouldn't scare me away, especially if you know (or can find out) which shop did the work. I would imagine rebuilding a 4.3 would not be a stretch for most shops.
  18. JASinIL2006

    Proper Engine Oil Level

    Mine is a mid-90s 350 Mag (a 5.7 essentially) and it takes 5.5 quarts. I wouldn't trust the SELOC manual for anything...
  19. JASinIL2006

    Proper Engine Oil Level

    I don't think, for any vehicle of mine I've ever serviced, that I got out the amount of oil that corresponded to the engine's supposed capacity. There's also the extraction method issue like alldodge mentions... sucking oil via the dipstick tube never seems to get everything out. Now, if you're...
  20. JASinIL2006

    Deck repair looks like might need new stringers and any other advice.

    Pulling the drive and motor isn't very hard; I am not in any way a gearhead in any sense and I was able to do it. Just make sure you take lots of pictures and label everything you disconnect. It does help to have an extra set of hands when pulling the engine, but most everything else is easy to...
Top