Search results

  1. M

    singing prop?

    I have just replaced my 11x9 prop with a 10.5x11 prop on a 35 hp evinrude. now it makes a whining noise at certain rpms. the performance works out for me but is this going to hurt anything in the long run and is there any way i can get it to stop whining? Or could it be the drivetrain making the...
  2. M

    35 hp evinrude bearing lubrication

    I have a 1976 35 hp evinrude. I started hearing a sqealing noise when throttling down or up sometimes but always when coming down off a plane. I'm worried it is a bearing sqealing. Now the parts manual shows the oil recirculation hose going from the lower crank bearing to the upper crank...
  3. M

    electric and rope start flywheel compatability

    I am wondering if the flywheels on a 1976 35 hp evinrude are interchangeable. I have the rope start model and found an electric start flywheel. It looks like it would work because it has all the rope start grooves and everything. To me they look indentical other than one has teeth. If anyone...
  4. M

    Upstate SC boat salvage yard

    Looking for a salvage yard in the upstate around the Greenville or Anderson SC area. If anybody knows where one is and can help me that would be great. Thanks
  5. M

    1976 35 hp evinrude flywheel

    hey guys I sheared a flywheel key and cracked the flywheel. Im looking for a boat salvage yard around the Anderson SC area or the upstate area in South Carolina. I keep hearing about some salvage yard up here but nobody can find it. If anybody can help me out that would be great. Thanks.
  6. M

    sheared flywheel key

    well i sheared my flywheel key on my 1976 35 hp evinrude rope start. the flywheel is junk because it cracked it but i think i can clean up the crankshaft and make it work but its not to pretty. does anybody know of a boat junk yard or something that might have a flywheel for me?
  7. M

    oil recirculation hose

    I just have a question because my service manual depicts two different pictures that show the oil recirculation hoses routed different. It is a 1976 35 hp evinrude rope start. The way I have it hooked up is the hose going from the top crankshaft bearing is going to the lower crankshaft bearing...
  8. M

    top cyl fouling on 35 hp evinrude

    i have a 1976 35 hp evinrude and the top cyl is fouling and not running on it at all because when i pull the plug wire it does nothing and when i pull the bottom it dies instantly. So the compression is 120 psi on both cyl, the spark will jump an easy 1/4 inch on both cyl, the point gap is...
  9. M

    running on one cyl

    i have a 1976 35 hp evinrude rope start. both cylinders have great spark being i just put new electrical everything on it. they jump a 1/4 inch easy. but when i start it, it is only running on the bottom cyl. i don't think fuel is an issue because the bottom cyl has plenty of it. but when i pull...
  10. M

    oil leak

    This is a 1976 35 hp evinrude. I have this oil coming from this hole in the lower unit and its engine oil. There is also oil coming out of the exhaust also unburnt engine oil. my first question is what is that little hole for and second does this just mean it is not burning all the fuel mixture...
  11. M

    1976 35 hp evinrude full throttle stop

    I am adjusting my timing and before i do that i need to set the full throttle stop. The stop got turned while rebuilding the engine and my question is that, is there any way to adjust this stop without running it at full throttle because i do not have a tank and it would have to be out on the...
  12. M

    Driver coil 1976 35 hp Evinrude

    I have no spark at all on either cylinder and have checked everything the book says and it looks ok as far as a regular ohm meter will tell me. I did notice that the driver coil under the flywheel the center coil is shorted to the other posts that are beside it that the screws go through. That...
  13. M

    water flow on 35 hp evinrude

    I have a 1976 35 hp evinrude and when i run the engine water comes out of the two cooling holes up top just fine. But it also comes out of the two holes right behind the steering collar on the exhaust housing. wondering if tho is right?
  14. M

    1976 35 hp evinrude leaf valves

    i just have a question about the leaf valves on my 1976 35 hp evinrude. the manual is very clear about the leaf valves needing to have a perfect seal and not to damage them. my question is that if the leaf valves do not seal perfectly would that make the engine run to lean of to rich?
  15. M

    still bad compression after rebuild

    I have a 1976 35 hp evinrude model 35602S and have just rebuilt the powerhead by boring the cylinders .030 over and new oversized pistons and rings. Along with all new gaskets and seals. It had horrible compression before in the 30's to 40's, cause it sat for a really long time and the cylinders...
  16. M

    bore out 35 hp evinrude

    I am going to bore out my 1976 35 hp evinrude model 35602S to .030 over. Install new pistons and rings. Is there anything else i have to do such as modify of change the carb or anything of that matter? Also will the original connecting rods work with the oversized pistons?
  17. M

    1976 35 hp evinrude cylinders

    I am wondering if anyone knows the dimensions of the original cylinder diameter for a 1976 35 hp evinrude model 35602S. I am asking because i am debating whether to just bore it out and put oversized pistons or put original pistons back in it with just honing the cylinders. I honed the...
  18. M

    piston ring gap

    I have a 35 hp 1976 evinrude and i just deglazed the cylinders today and i was wondering what the ring gap should be? I have new rings, they are the standard size and it took quite a bit of deglazing so i was wondering if i took to much off and if so would i just get oversized rings and file...
  19. M

    which way do pistons go??

    I have a 1976 35 hp evinrude and i'm doing an overhaul on it. I put new rings and honed the cylinders. I torqued the connecting rods and main bearing bolts on the crankcase halves. When i tried to rotate the crankshaft through, when the pistons got straight up and down it jammed up and would not...
  20. M

    1976 evinrude 35 hp torques

    i have a 1976 35 hp 35602S evinrude and am looking for the torques for the connecting rods on the piston, the torque for the crankcase halves and the flywheel nut. any help would be greatly appreciated thank you
Top