Search results

  1. alldodge

    Wonder if I should go IO again or go OB?

    Thanks Muc, as before your the go to guy. Never saw those kind of cost Was thinking about OB myself because I'm getting really tired of hanging upside down to change a bravo raw water pump impeller. Then just paying more then $1000 for a outdrive jack because I'm getting to old to man handel it...
  2. alldodge

    7.4L Overheating

    I don't see anything wrong with the impeller. Once it comes off the shaft it will distort
  3. alldodge

    Shift cutout switch not working even after replacement

    Which distributor?
  4. alldodge

    Happiest Day of Ownership !!!

    Math never lies
  5. alldodge

    2001Volvo Penta 50gl

    GLPEFS and as a non VP expert seeing the type distributor this should be it
  6. alldodge

    2001Volvo Penta 50gl

    GL what ? and assume your 50 is a 5.0
  7. alldodge

    7.4mpi just started running rough and with gas coming out exhaust

    All evens should not be tied together, only way this can happen is if someone moved the connectors. The below pic is from a 555 ECM but does illustrate batch firing better due to the colors. Injectors are seated with rubber type seals which keep it from grounding out against the intake...
  8. alldodge

    Happiest Day of Ownership !!!

    Might change the rear bunks from 2x6 to 6x6 and cut it to the same angle as the hull and low as possible. Move them in slightly inward so it will self center. My trailer came with outer 2x4 (flat side on the 4) bunks and it was so close to the strake that some times it would cause it to...
  9. alldodge

    2001 mercury 2 stroke 125 wiring harness diagram

    try here https://maxrules.com/wireindex.php
  10. alldodge

    4.3 won't turn over

    Serial number of motor and part number of starter
  11. alldodge

    4.3 won't turn over

    I would pull the starter and look inside at the flywheel. Could be your missing some teeth on the flywheel
  12. alldodge

    2002 Volvo penta Gxi 5.0 beeping issue

    Could very well be the wire connection Don't have a good wiring diagram, but finding pins 27 Knock 1+ 28 Knock 1- 29 Knock 2+ 30 Knock 2- But does not mention J1 or 2 but Merc should be J1 Having only one then should be 27 and 28 Should be a Bark Blue wire
  13. alldodge

    7.4mpi just started running rough and with gas coming out exhaust

    Use the noid of meter, turn key ON, motor not running and the light should be OFF. Or with a meter measure both pins to ground. Both side will measure 12V. If one measured 0V then there is a ground being applied
  14. alldodge

    Mercruiser 5.0 Won’t Reach Operating Temp

    Having a water connection like that you should have a Bravo drive. Does your water connection use a valve that is closed before running? If it does then I would go back to the Stat housing. Check the balls going to the elbows.
  15. alldodge

    Mercruiser 5.0 Won’t Reach Operating Temp

    Don't know if impeller is bad, but it was running to temp on a hose and the Stat was installed incorrectly. Normally even if the impeller is bad or week a hose will push enough water thru to keep the motor within limits, by pushing the water thru. You also have the spring and check balls which...
  16. alldodge

    2002 Mercruiser 5 liter MPI Distributor Timing

    might help
  17. alldodge

    Mercruiser 5.0 Won’t Reach Operating Temp

    Its not normal, might need to replace the impeller Have you verified the temp on the gauge with a IR?
  18. alldodge

    Need Help on 5.8fsi Couple of Issues

    Idle close to 700
  19. alldodge

    AC delco ignition

    Need to make sure and NOT listen to your marina. Nothing wrong or unsafe with TB ignition
  20. alldodge

    Wonder if I should go IO again or go OB?

    Not disagreeing but love to talk or hear more about cost of the two. Your the expert but just not seeing it. Popet valves, water pressure sensors, cat temp sensors, so many problems seen at the forum
Top