Search results

  1. Scott Danforth

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    switch to getting manifolds from BARR or Osco or Mercruiser.
  2. Scott Danforth

    Wooden Mounting Base with Casters for Mercruiser 4.3L 1992 Engine

    I used a shipping crate and some bits of 2x4. you can see it in this video. its sitting on the legs of the engine hoist which made it easy to lift the whole thing into the back of the truck i have also ran boat motors sitting on an old tire on the ground. you can also run them hanging from...
  3. Scott Danforth

    mercruser 888 wont rev past 2000 when in gear in the water

    What is base timing? What is all in? At what RPM? Verify the ratio. It should be 1.5:1
  4. Scott Danforth

    Advice On Stringer/Transom Repair

    go to the 3rd sticky down at the top of the forums. read links 14, 15, 18, 19, then the others.
  5. Scott Danforth

    Parking boat in driveway

    In my HOA, a parked boat must be behind a fence not visible from the street. lots of interpretation there as well.
  6. Scott Danforth

    mercruser 888 wont rev past 2000 when in gear in the water

    the two SBF firing orders are basically like an SBC/BBC 4/7 cylinder swap. it evens exhaust pulses, bearing loading and fuel distribution and smooths idle a bit. its good for about 5-10hp not enough to stress about unless trying to eek out every last bit of performance however that is the...
  7. Scott Danforth

    280 outdrive bell housing seal and bearing replacement

    first, welcome aboard second, get yourself the factory service manual from Volvo Penta Third, go here and look up current part numbers https://www.volvopenta.com/shop/0 fourth, read this. https://forums.iboats.com/threads/pds-shaft-issues.687012/
  8. Scott Danforth

    1962 Chris Craft Holiday 20’ bucket list resto

    How you doing Mike?
  9. Scott Danforth

    1971 Glastron GT160 Rear Drain Hole Question

    regardless of the motor on the boat, that transom started rotting about a month after the boat first came out. the encapsulation around the lower drain hole is abysmal. regardless if the splashwell drain was there or not. Im with Bondo, a good TOP on that boat (with a good...
  10. Scott Danforth

    Copper head gasket

    agreed on the aluminum.
  11. Scott Danforth

    1994 Mercrusier 4.3l engine compatability

    Im of the mindset, the block froze, why take a chance killing the next block with potentially freeze cracked manifolds. you could also put a 5.0/5.7 block in there, run the same accessories you have. you need a new intake and exhaust manifolds anyway.
  12. Scott Danforth

    1971 Glastron GT160 Rear Drain Hole Question

    Welcome aboard As an engineer and a realist, the aluminum plate is a bandaid applied over a broken back/legs/etc of the boats skeleton. it may offer a bit of comfort, however it wont keep the motor and transom attached to the boat unless there is also aluminum plates sistering the stringers...
  13. Scott Danforth

    Francine, Kenner, La.

    stock front suspension on the truck, or a grand marquis / crown vic IFS swap?
  14. Scott Danforth

    1985 mercruiser 3.0 starter

    I would replace the old direct drive starter with a PMGR myself
  15. Scott Danforth

    Crack in the Jon

    i would get it welded. if you dont want to do that, you need to rivet a patch panel over the crack and basically add some structure around it. the JB weld wont do anything in this situation but make your wallet lighter.
  16. Scott Danforth

    Outdrive question

    Did you read the tutorial on uploading pics? Try uploading from a PC as the forum pics have had issues for a while. On a phone you need to use the add files icon, then insert
  17. Scott Danforth

    1994 Mercrusier 4.3l engine compatability

    As of today there are 8-10 different generations of 4.3. Your current motor is a 93-95 vintage. Assume your intake manifold is trashed from the same lack of winterizing that killed the motor. Same for exhaust manifolds The next generation of motors are the 1996-2000, 2001-2007, 2008-201x...
  18. Scott Danforth

    Trying to determine proper engine/ trans/ prop pairing

    what pitch props are on the boat now? jumping 1000 RPM in props is about 4-6" in pitch you may not be able to prop that much since the motor is a replacement, is the throttle opening fully? right now there are a few million boats for sale as the marine market is stalled both new and used...
  19. Scott Danforth

    Trying to determine proper engine/ trans/ prop pairing

    only turned the motor 4000 RPM and stopped giving it throttle or did it only turn 4000 RPM with teh gear ratio and prop? Because the first scenario is someone too chicken to open the throttle, the second is over-propped scenario which kills motor. Until you @Will Steinbeck take the boat out...
  20. Scott Danforth

    I/O (Sterndrive) Conversion to Outboards

    His Brother Ondarvr posted about a decade ago on the wherabouts of Oops, However Even he is not longer a member
Top