Search results

  1. D

    06-5.7 mpi mag starts,, stalls, starts stalls. ran fine last fall

    A vacuum gauge reading will point you in the right direction , don't overlook exhaust restriction a vacuum gage reading will point this out too.
  2. D

    Mercruiser 165 I6 Exhaust flapper removal?

    I cut the 2 stainless steel riverts on the right hand side of the minor axis of the eclipse, then lifted the bracket up and pulled the old shutter and flatware shaft out
  3. D

    Durbans Johnsonator outboard motors .

    You see this is a 2006 model 4 stroke block with holes eaten into it by salt corrosion , only one of many more and more to come . in the 1st picture there is a hole between the 2nd and 3rd exhaust port looking from the left . in the 2nd picture you will see a hole in water channel opposite the...
  4. D

    Durbans Johnsonator outboard motors .

    Did some testing on my new Johnsonator motor.
  5. D

    Durbans Johnsonator outboard motors .

    Some testing from my new radiator motor that I designed.
  6. D

    Chrysler 75 hp. Difference in spacer plate to same motor?

    The function of that channel is for the water to flow around the exhaust area when and if your poppet valve still works you will also see a hole in the adaptor for the water to exit
  7. D

    Honda BF130 problems, needs input

    Do the job properly check the valves you may need to lap them check valve stem clearance and spring heights and replace valve stem seals
  8. D

    Honda BF130 problems, needs input

    I will just bring to your attention about these new type cylinder head gaskets .1st they tend to crack 2nd over the years the water friction removes the plastic coating on them and then they start leaking i would replace every 10 years uploaded i one from a mercury 4 stroke and one from honda
  9. D

    Honda BF130 problems, needs input

    the welsh plugs i was referring to put good thread sealant on if you gona drill and tap
  10. D

    Honda BF130 problems, needs input

    check replace this seal too and clean up salt builds up in there its on top of the pan where the gear shaft goes through
  11. D

    Honda BF130 problems, needs input

    Check your yoke too i fixed mine and put 4 coats epoxy after sandblasting
  12. D

    Honda BF130 problems, needs input

    Clean up your flush port as well i completely desalted my motor using Durbans nitric acid desalting formula
  13. D

    Honda BF130 problems, needs input

    What you can also do is behind your cam shaft you have 2 welsh plugs get some adenoids unscrew the welsh plugs and drill and tap and bolt the anoids to the inside of the welsh plugs this will prevent salt build up inside the cylinder head where you cannot see .the new cylinder heads look like this
  14. D

    Honda BF130 problems, needs input

    When i replaced my cylinder head it had a crack between no 1 and no 2 cylinder the newer cylinder heads the water passages are machined better to prevent it i put anodes in between the sleeves to prevent salt build up the depth is sufficient so i cut the adenoids to half the lenth of the depth ...
  15. D

    Exhaust deflectors

    This motor is used in salt water the deflectors are obsolete according to boat nets. So i did this with concrete and ceramic tiles the reason for the tiles is to change the deflection angle as the gas comes out the port , because over the years it eats away at the centure you will see in the...
  16. D

    65 ETEC won't start

    Iam still from the old school this is what i refered to as the carb . now days its called the Throttle body & works with TPS [ sensor ] which is located on the right in the picture
  17. D

    1986 timer base works on 1973 135 hp johnson

    My m8t needed help his timer base with 2 hall sensors where not working so i fitted a timer base from 1986 model it has 6 wires as apposed to 4 used the 2 blue & 2 green wires and wired it up to the 1973 power pack works perfectly .
  18. D

    100 hp ESL71A no spark at all

    My neighbor asked for my help i did a cross reference check on his ignition system the electrical drwg shows it has a sensor in the rotor,cross reference checked with a 1969 to 1970 ...85hp it shows a set of 2 breaker points &; it is also listed that these points are in the 1971 100 hp ESL the...
  19. D

    85 hp Chrysler Stator wires .

    I have 2 gray wires coming from the stator i bought this motor missing the rectifier for battery chargeing , i know the stator producrs AC volts i know how to connect the rectifier up just want to double check , does it matter on wich terminal the gray wires go on i also know one terminal out of...
  20. D

    W0T Timing in degrees DT SUZUKI 85HP model no 850-615276

    Any info on the wot timing setting in degrees would be appreciated , many thanks
Top