Search results

  1. Reserector_

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    I didn't want to dedicate a particular amount of resin to finish-coating only. I finished most of mine with waxed gelcoat, but later learned that gelcoat needs a good bit more hardener to make it kick. Some of mine stayed sticky until I brushed some release on it.
  2. Reserector_

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    Just in case nobody mentioned it, you want laminating (unwaxed) resin. No need to sand and acetone between applications because the surface stays sticky until you seal it so that the air can't get to it. Doesn't matter if it just cured, or if it's been weeks. Fresh resin reactivates the...
  3. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    My latest accomplishment was to finish the second seat and get it ready to mount. Photos of all the steps. Found a penny...I think it's a penny. LOL At least I had supervision on this part of the project. Pretty much snapped all of the old upholstery off, it was so brittle. Wood was long...
  4. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    They have a new site, in case you are not aware: https://www.caravellefans.com/ I hope it's OK to post that link. It is not a competing vendor. Just a brand-specific site.
  5. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I cut down one of my seat posts to the correct height, and set the assembly in the boat for a test fit. Or should I say "test SIT" I wish they could be taller for the sake of getting in and out of them, but I have to be properly positioned to reach the controls and see through the windshield...
  6. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I haven't ruled out wood wrapped in vinyl. Just exploring possibilities while I have time. I like the doghouse for the sake of engine access. Besides, none of us are sunbathers.
  7. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    The 1750 was also offered with a doghouse and a seat on each side. The seats could be folded inside out (for lack of a better term) to fill in and create the sun deck. Since It will mainly be my arthritic wife and I in this boat, I plan to go with a doghouse that will flare out to cover the...
  8. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I could mark the screw holes on the carpet, and then cut away the carpet where the screws will be so I can pre-drill and apply a small bed of sealant for each screw. I'm picturing a round piece of carpet about a half inch smaller diameter than the pedestal base.
  9. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    My main concern is about sealing. I don't want water to get under there and rot the screw holes. Maybe I'm overthinking it.
  10. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I have yet to strip and clean the second seat, but I went ahead and made all of the upholstery for it. This one waves in the opposite direction. My original plan for the steering wheel was to wrap the Teleflex wheel that I already had, but at best that would leave me with a nicely wrapped wheel...
  11. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    Hoping for more thoughts on trash receptacles. One more question: Glue down the carpet and THEN screw the seat pedestals in place, or screw the pedestals in place and cut the carpet around the pedestals?
  12. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    Random thought: The Coast Guard requires that I have a trash recepticle on board. This is a small ski boat. Maybe I can build something in while I am in this phase of construction. Any ideas? What do you guys use?
  13. Reserector_

    Beware of Shorelander/Midwest Industries Trailers

    Very common problem in the travel trailer industry.
  14. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I've been thinking about how I want to build the fiberglass engine enclosure. I want to make it slick-finished glass like it came out of a factory mold, but I want to shortcut the process by skipping the plug stage. I just want to build a single-use mold with a smooth-surface material...
  15. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    One seat is done. The other should be a snap because the patterns are made, and most of the parts are marked out, if not cut and sewn already. I reupholstered the seats in my truck five years ago with good success, but I have to say that covering these glorified plastic buckets is more...
  16. Reserector_

    How many gallons of resin?

    I did a 17' ski boat complete with 12 gallons. I took the time to hard roller the air out and keep the layers compressed as I wetted it out. Lighter and stronger if you put in the effort. If you just saturate it, you will need a good bit more. Floor alone will take 3 to 4 gallons with the...
  17. Reserector_

    165 L6's out of the bertram. What do they need?

    While you are resealing the engines, consider replacing the rear main seal and the front crank seal in the timing cover. Especially since you plan to reseal the oil pans. The differences that I have seen in marine grade parts is that they are either sealed, or as in the case of alternators...
  18. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I ran this pass through five layers. Front side photo, it's the pass on the right. Back side photo, it's the pass by my thumb. This seemed to be the physical thickness limit for this walking foot attachment. Tension is consistent whether two layers or five.
  19. Reserector_

    Where to pick up power for electric choke?

    My OMC is connected to the AC tap just as Lou C explained. Running to a key-switched source will work, but as soon as you turn the key on (with the flame arrestor removed) you can watch the choke slowly open. That's how it is with my Holly. Rochester may have a stepped cam that prevents it...
  20. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    Using V-92 polyester. Needles are #18 round point.
Top