Search results

  1. O

    Broken Knock Sensor

    So while draining the water out of my block I managed to break the knock sensor on my 2005 5.0 GXI-E. I found a replacement for about $70. I don't have a problem spending that to fix it. But, what I'm wondering is if I can go to my GM dealership and order the exact same thing for a much lower...
  2. O

    GXI-E Spark Plugs

    I'm getting my 2006 Four Winns ready to put away for the winter. The engine is a Volvo Penta GXI-E. It has 300 hrs on it so I figured new plugs are in line this time. I pulled an original and it was an AC 41-932. I found out that the 41-932 has switched to a 41-993. No problem except I...
  3. O

    VP Fuel/Water Seperator vs WIX Fuel Filter

    I've always used a Volvo Penta #3862228 Fuel/Water Seperator on my 2005 Gxi-E. This number crosses to a WIX 33359 which is just labeled as a fuel filter. Is there a difference? They look the same, whats the water seperator part?
  4. O

    Is Mobil 1 10w-40 ok in my engine?

    Im sorry to post another engine oil question but I need some input. I've always used Volvo Penta 30wt synthetic in my 2005 5.0 Gxi-E. I see now that Volvo only sells 10w-40 which I assume is a suitable replacemnet for the 30wt. My question is, Is there any reason I couldn't use Mobil 1 10w40...
  5. O

    Are bellows ground straps necessary?

    I forgot to reattach the small ground strap under the hose clamps when I put new bellows on. Are these even necessary? Why would you need to ground the hose clamps?
  6. O

    Can anyone help me find this yoke?

    I have an '05 SX-M 1.66 with the GKN driveline assembly. In my infinite stupidity I bent one of the ears on the short yoke while changing u-joints just enough so I now can't get the retaining ring into the slot. I could bend it back but am afraid that if it's even a little out of balance I...
  7. O

    Greasing a new gimbal bearing

    I just installed a new gimbal bearing in a SX-M. When I greased it the only grease that squeazed out was between the outside of the bearing race and the housing. Shouldn't the grease squeeze out between the bearing and the race first? I'm afraid the ring that rotates around the outside of the...
  8. O

    Rockwell and GKN Yokes Interchangeable?

    I need to replace the short yoke in the driveline on my '05 SX-M 1.66. The yoke I have now has GKN stamped into it. I the genuine volvo parts section if I want GKN I have to buy the entire driveline assembly. However I can buy jusy the yoke in the Rockwell setup. Can I replace the GKN yoke with...
  9. O

    Gimbal bearing, bellows, u-joints - what else?

    I have an '05 VP SX-M drive. I recently noticed that the drive was making noise and was much worse around 3000 RPM and turning right. I pulled the drive off and am pretty sure it's the gimbal bearing. When I spun the bearing by hand it was smooth but made a little noise. I'm going to take the...
  10. O

    Iridium Plugs?

    Is it ok to replace the platinum plugs on my '05 5.0 GXi-E fuel injected with iridium plugs? It currently has Delco 41-932 plugs in it, what iridiums should I replace it with if it's ok?
  11. O

    Hairline cracks in Stern

    Re: Hairline cracks in Stern Here are some pics.
  12. O

    Hairline cracks in Stern

    I was recently winterizing my '05 Four Winns when i found a couple of hairline cracks in the stern extending away from where the drive mounts. They appear to only be in the gel coat. Is this common? I assume that I need to seal them up somehow before I get any water penetration. Any...
  13. O

    Hard Starting '05 Volvo

    I have an '05 Four Winns with a Volvo 5.0 GXI-E. I've noticed this season that the boat will fire right up when put in the water. However it will run for about 3 seconds and then quit. It is then hard to start, I have to pump it a bunch of times and have the throttle about 1/4 open in neutral...
  14. O

    Looking for opinions on Four Winns

    I've recently come across a 2005 Four Winns 200 Horizon with 125 hrs. The boat, so far, seems to be in excellent shape and well taken care of. The owner is asking $15,500 which doesn't seen too bad. Any opinions on Four Winns boats or things to look for would be greatly appreciated. The motor...
  15. O

    1991 Sea Ray 250 Sundancer - Need opinions

    Ok, I've found another moneypit. It's a 1991 Sea Ray 250 Sundancer. I've never owned a Sea Ray and I think they have a good reputation. This boat has a 7.4 liter and a bravo one. The boat has 400 hrs and looks like it's been very well taken care of. Any opinions or advise on this boat before...
  16. O

    Wellcraft Elite 220XL

    I recently came across a 1988 Wellcraft Elite 220XL with a newer 260 Merc. and a rebuilt Alpha 1. It's a 4 hour drive to go take a closer inspection. What can you tell me about these boats? I've learned many things in these forums and just want to make sure the drive is worth it. What would you...
  17. O

    Looking for opinions of OMC Cobra

    I recently found a 1990 Chris Craft 247 LTD with a 460 OMC Cobra (340 HP). I have no experience with this boat or engine and was wondering what you all could teach me. Everything looks great in the pictures and I was just wanting some input before I drove 300 miles for a closer inspection.
  18. O

    Cracked Hull

    I bought a 20' Cobalt earlier this spring an have had the boat out many times. The boat is great except it leaks pretty good. I finally had some time to investigate. Under the outdrive on the exterior was a bunch of silicone caulk, I assumed this was the problem area so I filled the hull with a...
  19. O

    Gel Coat Cracks

    I have an '88 Cobalt 202 and have recently noticed cracks forming in the gel coat. Mostly around where hardware is mounted to the fiberglass. They are only hairline cracks so I assume they are limited to the gelcoat and not through the fiberglass. Do I need to be worried about these cracks and...
  20. O

    Clicking from Sterndrive

    I have an '88 Alpha One. While on the trailer and the drive all of the way up I spun the prop by hand. Turning clockwise everything sounds fine but turning counterclockwise there is a clicking noise. Is this a concern? I'm assuming my shifting cable is out of adjustment, am I correct?
Top