Search results

  1. KRH1326

    Adding Raymarine ST5000+ autohelm to a Garmin system

    Hello, I purchased a boat, that came with a ST5000+ Autohelm. It had been connected to a Lowrance unit, via nmea 0183, and was working fine. Previous owner removed his Lowrance systems. I installed my Garmin system .. multiple gpsmaps, radar, livescope, heading sensor, etc etc all connected via...
  2. KRH1326

    SportCraft sliding windows.

    Hi All, haven’t been around in a loooong time, and I hope everyone is doing ok. I haz a new to me 2001 SportCraft 272 express sport fish. there are sliding windows, at helm, Port & starboard. Two piece sliders , fore and aft. The two forward pieces easily slide back, but the aft two pieces...
  3. KRH1326

    1990 90 HP Charging Issue

    hi everyone... been a while since I was in these forums. im not a Merc guy, and this issue is driving me crazy. It’s my son’s, new to him, 1990 90 HP. It looks like serial number 0C272485. it has a low amp stator and a rectifier... no regulator. Simple three terminals on rectifier. The ++ term...
  4. KRH1326

    FIPS issue

    Hi Guys, I bought a new vhf with dsc, and am in the process of setting up some features. The manual says that I can enter 6 digit FIPS codes, so that I can receive alerts that are that area specific. The radio wants 6 digits, however the best I can do is 5 :-/ Ex... NY is 36 and Suffolk County...
  5. KRH1326

    Tilt N Trim Wiring Issue

    Hello All, Replaced my 1987 175HP Crossflow with a 1997 175HP Looper. All switch overs have gone well, except for the tilt / trim cable, to my remote. The existing cable is a round, black, rubber plug with 5 wires... while the new motor has a plastic, triangular plug with 3 wires. The harness...
  6. KRH1326

    Resolved

    Resolved
  7. KRH1326

    !987 Evinrude 175 HP E175TXCUA Running Issue

    Hello All, I have two identical motors. Motor A threw a rod, and was sidelined. Was using motor B, until a head gasket failed. Opened up motor B, to install new head gasket, and found cracked cylinder. Completely stripped blocks A and B down to case halves. Rebuilt existing motor from case...
  8. KRH1326

    Evinrude Service Bulletin ????

    1987 Evinrude 175 HP E175TXCUA - Engine reassembly is coming along nicely, thank you to those who have helped me thus far... Getting close to Intake manifold and carbs. I was told that these cross flow V-6's were prone to ring and/or piston failure due to carbon build up, which is the cause of...
  9. KRH1326

    OMC Gel Seal vs. Indian Head shellac based compound.

    Hello all.... Happy Labor Day weekend !! The reason that I ask is, I have 'exclusively' used Indian Head for several decades, on every motor that I have wrenched. From Detroit V-8's to Milwaukee V-Twins, and have had no problems or regrets. I have to reassemble my Evinrude 175 case halves. My...
  10. KRH1326

    1987 175 HP ( V-6) ByPass Cover Removal

    Hi All, Am working on my 1987 Evinrude 175 HP. I need to remove the bypass cover. I have the engine stripped down to the cover, at this point. Do I HAVE to remove the entire power head? I VERY much just wish to remove the cover as is, and get on with my mission. I can see the smaller bolts...
  11. KRH1326

    Evinrude Cylinder Sleeve

    What metal are the cylinder sleeves on a 1987 Evinrude 175 HP v-6 made of?
  12. KRH1326

    1984 9.9 HP Extended Long Shaft Yacht-twin water pump issue.

    Started up my 9.9 , and found no water at the tattler. Purchased pump and housing kit last night, and dropped the lower, first thing this morning. I tried to push some compressed air, up the water tube, but only got a barely noticable amount of air at the tattler. As of right now, I only have...
  13. KRH1326

    NMEA wiring issue with Garmin 541S and Uniden UM380

    Hello All, Racing to get my prep work done and of course, Garmin and Uniden's Customer Service/ Tech are closed for the whole weekend.... I am utterly confused with the NMEA wiring, as Uniden shows two different drawings, and Garmin's is different, as well. Can someone help me sort this out...
  14. KRH1326

    Red Lever ?

    Hello Everyone! I have a new to me 1987 175 hp Evinrude. I just started it up, supposedly, for the first time in a couple years. I got it to run, but was at a fast idle, and really started searching around the carbs. I found a small cylinder with a red lever on it, on the starboard side, right...
  15. KRH1326

    Temp gauge question.

    I have an 87 175HP Evinrude. In the factory harness, is a tan wire, that goes to the warning horn, that is for temperature. Can I split that wire, and use is as a "sender" or "signal" wire to a temperature gauge? Thanks guys!!
  16. KRH1326

    Can any of the Guru's help me identify a model year?

    Hi Everybody! Bought this new to me Evinrude, and was told it was a 87 or 88 model 175 HP. The model and serial tag on the port side of the bracket is missing, so that doesn't help. Any tell tale signs to look for? Thanks
  17. KRH1326

    Winter stake for mooring

    Hello Everyone, Happy New Year. I ran a search for ( winter , stick, stake ) and no results came up, so I have to ask.... What is the best way I can make a winter stake for my mooring, that is sitting in about 5-8 ' ( low tide ) ? I have found some articles that contrdict each other, so...
  18. KRH1326

    Humminbird FF Question

    I am contemplating purchasing a new fish finder. I am trying to stick with Humminbird ( I have had several products, and am comfortable with them), while staying in my available budget. The two that I am looking at is the 718 or the 570. They are both do-able for me, but I don't understand...
  19. KRH1326

    Cam Synchro/ TDC/ Rebuild Question

    Hey Guys, I know, maybe this should have been posted elsewhere, but the folks that I want to ask are here, not there. In the proccess of rebuilding the 3.0 v-6 vulcan in my 1999 Ford Ranger. Pistons, crank, cam, lifters, cyl heads, timing gears and chain, timing cover and oil pan are...
  20. KRH1326

    Holiday Cards For Our Oversea's Troops

    I don't know if this violates forum rules, if it does, I appoligize, and did not intend to. I got this email from my union's COPE office. I checked the SNOPES.Com site, and it claims that this is true and working. I just let my kids send out a bunch of the cards, and tried to explain where...
Top