Search results

  1. T

    Hard to start

    1959 18 evinrude. New points, condensers, coils, ignition wires the steel type, and plugs. Rebuilt carb last year, fresh gas premium 25 to 1 oil mix. Compression is 115-120 on both holes. What am I missing? Even bypassed the stop button at the points. Have lots of blisters and no satisfaction...
  2. T

    30 weight oil in older outboards?

    On the side of my gas tank it states use 1/2 pint of oil with every gallon of regular gasoline. Reccomend outboard motor oil or any sae 30 weight regular automotive engine oil. It's a '59 18hp evinrude used only one season. I thought it was 25:1 only outboard motor oil. Whats the deal with...
  3. T

    Motor jumps out of gear

    1965 Johnson 9.5 hp jumps out of forward into neutral. Will stay in reverse. Would this be a linkage adjustment or drive dog issue?
  4. T

    leak L/U to boat transom

    Tried to remove L/U omc cobra. It only came out 1.5 inches, so I put it back together. Now it leaks when in water. What might have I done to cause this?
  5. T

    dies at advanced throttle

    4.3l, twobarrel holley, starts great idles great, gets up on plane but if throttle is advanced higher motor dies. Then will start again at idle. carb removed and checked for debris, but looks great. new fuel/water filter and fresh gas. boat sat for 5 years. tank had 1 lire of gas in it witch was...
  6. T

    Motor won't turn over

    :(ChrisCraft 177GD, HIN-CCVGD302A090, Cobra outdrive Model # 986032, Motor Model # 432APRPW5. Has 176 hrs on the meter. Boat has been sitting for 5 years. won't turn over. removed plugs (they were brand new) and squirted 2 oz of two stroke oil into each cylinder. Afraid to torque nut too hard...
  7. T

    Remove lower unit to access water pump

    1977 175 johnson. There are 5 bolts as far as I can see but the l/u will not budge. Shifter linkage is removed as is entire powerhead. Am I missing something? Please help. Thanks, Peter
  8. T

    Age of this motor ?

    Does anyone know the age of this 9 1/2 hp Johnson Outbard Motor Model # MQ - 11c Serial # 0346071
  9. T

    Steering really tight

    How do I go about freeing up a real tight steering system. 175 hp johnson on a 17 foot deep v with what I assume is rack and pinion at the helm and a flexible cable to the motor?
  10. T

    Break In

    How do I break in a freshened up motor. V6 crossflow, #1 cyl rebored to 2nd over, new piston and rings, #2 through #6 honed and new rings.
  11. T

    Looking for 1977 175 crossflow block

    Been searching for a used block for months, most found are too corroded (water jacket leaks) or already 3rd over. Some, the prefered choice, were dipped in a reddish primer/ceramic type paint that sealed the aluminum in the water jacket areas. Prefer canadian location due to shipping...
  12. T

    Compression/rings?

    77 v6 175 after a long run, warm engine #1-75 #2-6 110-115 1 oz oil added to #1 reading jumps to 120. Is this a ring issue? Would a decarb help diagnose problem. Whats involved in ring replacement?
  13. T

    Starting

    Is it common on a v6 if it is tilted up as in shallow water that it's very hard to start?
  14. T

    #1 cylinder not firing

    1977 Johny, 175 V6. Compression 95 #1, 100 all others. Usually runs on 5 of 6. #1 plug wet, all other plugs look good. New plugs(surface gap type), had conventional plugs when purchased and problem existed. Switched #1 plug , coil, and lead, from powerpac to # 2 cylinder and all # 2 cylinder...
  15. T

    Power tilt and trim

    1977 175 johnson. Tilt/Trim motor runs but no response from engine. Filled reservoir with motor in the up position and checked manual override screw. seems tight. No leaks but I'm stumped on this one. Any suggestions?
  16. T

    1977 175 Johnson V6

    Considering buying one. What to check before making decision. Compression numbers, wter pump operation, lower unit integrity, ie seals etc. Any advice would be helpful. Thanks. Peter
  17. T

    compression not good?

    69 johnson 6hp. 60psi top, 80psi bot. Is this motor toast?
  18. T

    Hard to start

    1959-18hp evinrude. Engine is run with gas line off before putting away. When starting after a week or so it takes many pulls to get it going. Won't idle well until really warmed up like 10 minutes at wot. It does puff out of the carb during idle when not warm. Lo jet is @ 1-1/4 hi is at 1/2...
  19. T

    Water In Lower Unit

    18 hp evinrude 15028-07596 Golden Jubilee - What year is this? Have more water than oil in lower unit. Replaced oil but it is leaking. Are prop shaft seals still available for this unit? Do I need a new gasket for the lower unit when replacing the seal? What is the proceedure for doing this...
  20. T

    1968 55hp evinrude upgrade ignition

    Has anyone got the definitive answer as to how to sucessfully convert a 55hp 1968 triple to run with a coil,condenser and ballast resistor setup? I've viewed many threads on this site and still don't have the full scoup!
Top