Search results

  1. T

    Yamaha F250 valve clearance -- all exhaust valves too tight?

    2005 F250 w/ ~2,000 hours. Unknown maintenance history. Checked all valve clearances per the service manual. All intake valves are .178-.203 mm (within .17-.23 tolerance). All exhaust valves are .229-.279 mm (all tighter than .31-.37 mm tolerance). Seems a bit unusual. I've pulled the shims...
  2. T

    [SOLVED] Alpha One won't shift into forward -- jam nut loose

    I have read the manual..w/ lower unit in forward & bungee holding prop CCW, set adjustable stud to bottom of slot, set lower barrel to 6" then set upper barrel w/ light pressure on cable and back out 4 turns. Move adjustable stud if necessary to shift into reverse (holding prop CW). However...
  3. T

    Alpha One -- weird serial number, A335515F

    Trying to determine whether this is a gen 1 or gen 2, and the seller tells me the s/n on the upper is: A335515F Maybe an aftermarket??
  4. T

    Vacuum fluctuates 9-13 at idle, then steady 18 at 1300rpm

    Yes I have searched & viewed these 2 good sites: http://www.secondchancegarage.com/public/186.cfm http://www.imperialclub.com/Repair/Fuel/VacuumGauge/index.htm This is a 1987 Mercruiser 260, 4bbl Quadrajet. Engine has 145-160psi compression all the way around. The vacuum fluctuates from 9-13...
  5. T

    Mercruiser 260 (Chevrolet 350): water in oil & #1, #3, #5 cylinders

    #1, #3: 85psi compression All others: 140-160psi compression Pressure test of coolant system showed leaks into #1 & #3 Head gasket shows a break between cylinder & water jacket on #1 & #3. Any ideas what could cause this?
  6. T

    Quicksilver throttle control loose

    I have a Quicksilver panel mount throttle control. The manual is here (thanks Don S) http://www.4shared.com/account/file/48885382/2933ae0b/Commander_Panel_Mount_sec04.html The throttle control is loose to the point where it no longer engages. The plasting "bezel bushing", labelled part #22...
  7. T

    Mercruiser 350 Quadrajet: stock jets/rods?

    I am trying to track down a clicking noise at high rpm/load http://forums.iboats.com/showthread.php?t=286177 Possibly due to a lean condition... So I've disassembled the Quadrajet. Haven't found any dirt or any passages plugged up yet. Needle & seat were clean. Soaking everything that's not...
  8. T

    1987 Merc 350 noise at high RPM, timing related

    I have a completely stock 1987 Merc 350. Compression 150-180psi all cylinders. Recently replaced heads after discovered water in the oil, low compression in cylinder #5. Found leak in head gasket between water jacket & cylinder #3. Found crack in head on #5. The timing is controlled by an...
  9. T

    Louisiana: Tchefuncte Tickfaw Amite Diversion

    Went out Saturday and found the Prop Stop & Tin Lizzy's were closed...only a handful of people on the water. Are there other spots in the area that extend the season into October?
  10. T

    Saltwater boat in storage facility; where to flush?

    I have an 87 Mercruiser Alpha One that I run in saltwater, and I store the boat in a storage facility (that doesn't have a water spicket available). Anyone else in this situation? What do you do to flush the engine? It's kind of impractical to stop by the house to flush everytime. Anyone...
  11. T

    Mercruiser 350: clicking noise at high RPM

    Had the engine apart to replace a head gasket. This is a 1987 Mercruiser (Chevy) 350 w/ Thunderbolt IV electronic ignition (yes it has electronic advance). Also replaced spark plugs with same plug number, but an updated (looked a bit different), AC Delco MR43T. Put it back together as per SELOC...
  12. T

    Boating in Louisiana: where to go?

    Hey guys, I'm new to Louisiana (New Orleans area) from Michigan. Just bought an 87 Baja Sunsport 196 in great shape. Been out to Lake Pontchartrain, the Tchefuncte, and the Bonnet Carre Spillway. Hoping to make it to the Tickfaw and Bayou Segnette this weekend. Looking for a place to cruise...
  13. T

    1987 5.7L Merc: sometimes won't crank

    Sometimes when I hit the key, the starter engages but won't crank (like the motor is locked up). Hit the key again and it will crank. (sometimes does, sometimes doesn't) I don't think it's a bad battery...it's only a few months old and when it does turn over the battery is capable of turning...
  14. T

    How to check lower unit oil for water

    After reading about the drive bellows and how quickly it can take out U-joints, gimbal bearing, etc. I'm going to make a point of checking the bellows and lower unit oil for water every couple of trips to the lake. What's the easiest way? Drain a little and look for milky oil, take the top...
  15. T

    Testing exhaust manifolds / risers / elbows (Mercruiser, probably others)

    http://forums.iboats.com/showthread.php?p=1724605#post1724605
Top