Search results

  1. F14CRAZY

    Resealing 3.0L Stringer/Series 400

    I'm looking to install new shaft seals in my sterndrive before this summer. I've searched and found a number of suggestions, but what sealant/gasket maker/compound/etc should be used between the shaft seals and the housings they're seated in? Thanks guys
  2. F14CRAZY

    18' Thompson Calae transom, stringers and deck

    I'm back again... In 2008-2009 I did the thread at the bottom of this one. Not really knowing anything about boats or glassing, I took on the 19' Bayliner Capri 1952 I had just bought. And its held up great after almost 9 years. I'll link to the old thread I had here but this forum helped me...
  3. F14CRAZY

    ESA kicking in by itself

    '85 Series 400, 3.0L in my Capri. Randomly while cruising the engine will drop RPM and stumble like when the electric shift assist is making the ignition miss while shifting (switches were properly adjusted and not pressed when shifted in gear). I disconnected the 4 pin connector and its run...
  4. F14CRAZY

    Hydraulic (trim) cylinders for an AATV/swim platform

    What are typical sterndrive trim cylinders made of? I'm under the impression that they're aluminum with stainless rods. While this project is far from being under progress I've been brainstorming ideas on fabricating a hydraulic swim platform for my Coho to carry my 6x6 AATV as a dinghy. I'll...
  5. F14CRAZY

    Chris Craft 327QA compression test and analysis

    The diagram above is reversed...the engine marked 1 is port, 2 is a starboard. The two cylinders for reasons unknown had water shoot out when i removed the plugs and turned it oVer via the starter. I swore i removed the plugs and cranked it over when i took delivery of the vessel. There's an...
  6. F14CRAZY

    Recoating ablative bottom paint...do I have to?

    Boat in question is my Bayliner Capri... Before last season I added a few coats of Interlux Interprotect epoxy barrier coat along with 3 coats of West Marine CCP ablative bottom paint, in blue if it matters. Was slipped in the Grand River from June till October. I didn't do anything as far as...
  7. F14CRAZY

    Evinrude 90 hp lower unit

    My girlfriend's stepdad is acquiring an '80's 17-18' bowrider with a 90 hp Evinrude. The deck, stringers, transom, and power head seem to all be good, so no worries there. However, the lower end was removed for some issue a couple years ago and was to be repaired by a neighbor or friend, and...
  8. F14CRAZY

    Converting from I/O to V drive inboard

    I'm tired of sterndrives. The Series 400 in my Capri isn't too far from shot. I re-sealed it before last season but ALL 4 compartments at the end of this season were somewhere between a milkeshake and creamed coffee. I pressure/vacuum tested too. I figured the ridges on the seal surfaces tore up...
  9. F14CRAZY

    Resealing outdrive...ridges where seals ride

    What's the best way to remove the ridges formed by the lip seals on shafts and gears? I need to reseal my Series 400 again...its leaking in water in EVERY submerged oil compartment. Is a lathe needed? I'm pretty sure this is why my first attempt wasn't successful (hey it was a couple years...
  10. F14CRAZY

    Adding seawater strainers?

    My Coho doesn't have any strainers on the seawater intakes. Should I consider adding them? The Grand River which I have a slip on and boat on tends to have a fair amount of small junk, like leaves and little twigs after it rains. The grates on the intake scoops are pretty small but should I be...
  11. F14CRAZY

    Here we go...33' Chris Craft Catalina Coho sedan!

    I'm not new to this kind of stuff...but in a way, I am... http://forums.iboats.com/showthread.php?t=272749&page=9 I've been thinking of owning a "classic" Chris Craft in this size for a long while but wasn't planning on buying one yet due to a car loan I'm still working on. But in the meantime...
  12. F14CRAZY

    First time purchasing and piloting an inboard boat...suggestions?

    Alright, here we go... I'm looking to purchase a low dollar '71 Chris Craft Catalina Coho 33' with twin Chris Craft 327's. Mechanic at the boatyard said they start and run fine along with pumping water fine. I've been inside and out of my OMC sterndrive and general automotive experience but I...
  13. F14CRAZY

    Considering restoring a wooden Chris Craft cruiser

    I'm considering taking on a big project, a 1964 (or so) Chris Craft Sea Skiff 32'. Twin 327s, I think, and lapstrake plywood planking. It's a big cruiser like a Constellation but a Sea Skiff because of its lapstrake hull. It's located at the marina my Bayliner is at (on the hard) and I can get...
  14. F14CRAZY

    Trouble aligning 351/ 233

    My best buddy has an '82 Wellcraft Nova 21' where someone swapped out the original 351 and put in a 302. Sterndrive is marked 233 and the holes where the 351 was attached to the engine mounts were not sealed and so they were rotten. We pulled out the 302, I cut out and glassed in new engine...
  15. F14CRAZY

    CSM before laying roving?

    I'm glassing some new engine mounts in my buddy's Wellcraft. Is a layer of CSM required before laying the 18 oz? Using premium polyester resin not my usual epoxy. Thanks
  16. F14CRAZY

    3.0L ESA and missing when cold

    I have two separate issues... I found that my ESA was kicking in randomly while cruising even with the adjustable things removed from the shift converter. Engine would bog randomly. After checking or replacing about everything else I disconnected the ESA and it cruised fine all weekend. Do I...
  17. F14CRAZY

    3.0L bogging/hesitating after running a while

    On 3 occasions now (two last season, and one today) I was cruising around 3k-3500 rpm and out of nowhere the engine will start running crappy and hardly go above idle. I can give it a little throttle above idle or WOT but it just bogs, stumbles, and won't hardly go above idle. Does it in forward...
  18. F14CRAZY

    What really is bad about OMC drives?

    What makes OMC sterndrives the ones to avoid? I understand that they don't make them anymore but my local Evinrude dealer still can get parts that I ask for for my 3.0L Series 400 and their service department still has the special OMC tools along the wall. GLM has new gears and bearings. Were...
  19. F14CRAZY

    Barrier coating hull before bottom paint

    I have an '85 Bayliner Capri which has never had bottom paint. I intend on keeping it in a slip this season on the Grand River in Grand Haven. I picked up a gallon of West Marine CPP ablative antifouling bottom paint. The manager strongly suggested I use a barrier coating (Interlux Interprotect...
  20. F14CRAZY

    Bottom paint for keeping my boat in a slip

    My girlfriend and I have been thinking hard about keeping my Bayliner in a slip not too far away for the summer. Its been a trailer boat all its life and the hull is still virgin fiberglass. From searching old posts I found the practice to be to wipe with acetone, sand with 80 grit, probably...
Top