Search results

  1. B

    gearboxes on inboard engines?

    got a 140 bhp v8 car engine here which i wouldn't mind throwing into a boat for a laugh. What is the situation with auto gearboxes and boats? are they used? or are the gear changes not smooth enough for an outdrive... perhaps too 'jolty' at the gear changes? I always thought that just using the...
  2. B

    17ft owens on road to recovery

    Thought i'd post a few pics of my ?50 owens. Almost finished the thing. Wite flowcoat next week and then need to fabricate an anchor and find some life jackets! Cleaned out under floor and replaced surface. Today lubed and installed electric shift, powered bucket seats (bit heavy, will make...
  3. B

    plasti wood instead of wood that rots?

    This might have been covered before but has anyone thought of using that plaswood - recycled plastic wood instead of ply and timber in stringers, transoms and floors? It doesn't rot and i believe you machine and cut it on woodworking machines, just like wood. I have seen it in the flesh on some...
  4. B

    can i launch withwet underfloor foam?

    got a boat from the 60's here and lots of water got into the underfloor when it was stored under a leaking barn roof.. drained it out, took an hour. black as you like... probably from rotten ply. Now its all dry, can i launch the boat on its maiden re-launch? i assume if the boat gets swamped...
  5. B

    What foam, timber or ply for floor?

    Anyone got any tips on type of timber for remaking the stringers and deck? Using the boat at the mo but come winter will cut the floor out and repair /replace etc. At the mo there are numerous soft patches and it looks as though water was getting in where the seat bases were screwed down... as...
  6. B

    Anotherdodgy deck and probably soaked foam

    Usual story. Anyone got any tips on type of timber for remaking the stringers and deck? Using the boat at the mo but come winter will cut the floor out and repair /replace etc. At the mo there are numerous soft patches and it looks as though water was getting in where the seat bases were screwed...
  7. B

    Fuel tank reconditioned. Pump needed?

    Yo boat folk. Now the army events are almost all over i can get back to finishing the boat... Now, where was i...? Oh yes.. the fuel tank. Spent the afternoon plumbing in new fittings. This tank was in pooooooor shape. Pulled out residues the size of a football.. really! 10 year old fuel with...
  8. B

    can my stern drive handle 150 BHP?

    alright all. been given a 150 brake horsepower V8 engine which i will put on the shelf for the day when my V4 packs u (its old and i reckon the water jacket will fail as salt water was left inside). The V8 has an alloy block and head which is great for weight, (its lighter than the V6 which was...
  9. B

    boat roof cover - any plans and build your own?

    I am planning to make up a hinging frame and cover in the style of a folding boat roof. Does anyone know of some simple designs online anywhere? I have noticed that a lot of boat roofs have a main pole leaning back with a long one spurring off it forward above the windscreen and a smaller one...
  10. B

    boat roof cover - any plans and build your own?

    I am planning to make up a hinging frame and cover in the style of a folding boat roof. Does anyone know of some simple designs online anywhere? I have noticed that a lot of boat roofs have a main pole leaning back with a long one spurring off it forward above the windscreen and a smaller one...
  11. B

    V8 engine... which outdrive to use?

    I have a V8 engine coming and need to know which stern drive will be correct for it? It is from a Range Rover and produces about 180 bhp. In the UK mercruiser and volvo are very common. Can anyone recommend a type to look out for, that doesn't cost the earth, is not a complete ba***rd to repair...
  12. B

    Flame Arrestor - A Good Idea?

    I have read about the use of a flame arresters on the carbs of my inboard engine (in the manual). Are these something that are still recommended or is a standard air filter adequate? Engine is ford Essex marinised V4 2L with twin SU 32 / 32 carbs. 17ft owens, OMC stringer 1968 outdrive
  13. B

    shimming top cap / lower gear housing?

    hi there. Noticed my lower gear housing wasn't sitting snugly under the upper gear housing and the very large o ring / seal was quite loose. Would i be right in thinking that the stern drive top cap (4 bolt) needs to be shim'd upwards as this is the only way to make these two meet? I have done...
  14. B

    Omc Stringer Long Shaft Mystery Over

    Result. Thanks to googling 'lomc ong shaft' i found an old iboats chat about the same. In one of the responses was a partial screen grab of BRP Parts online website and parts list. After browsing through this i can confirm that i have found my upper and lower gear casing and parts which are...
  15. B

    what hp and posible speed my boat and weird engine combo?

    Yo. Has anyone got any idea of the speed my boat will do or what bhp it might be? got the whole lot for 50 pounds and it didn't come with no manual man! its a pretty light owens 17ft speedboat with no cabin, just a perspex windscreen. 80 Litre fuel tank in the front and a 2 litre v4 petrol...
  16. B

    omc stringer drive pumps a tonne

    fixed the water pump! thanks to all who gave advice. The problem was that someone either drilled a hole in the impeller housing or there was some sort of access hole that had a bung which went missing. As soon as i plugged it (liquid metal) the pump worked. Either way, in the process i serviced...
  17. B

    omc pre 77 stringer manual non clymer

    hi boat type folks. anyone digitized a manual for the omc pre 77 stringer drive that isn't a clymer? if so, can i download it? nice one guv
  18. B

    can anyone recommend a 12 volt raw water pump ?

    i need the pump to provide water flow for my hybrid v4 and Omc stringer setup. It is very old and has issues that arent worth throwing money at ! I i would possibly need i water scoop pickup pipe also if i cannot create a sealed water jacket in the stern drive. Thanks
  19. B

    help needed with omc pre 77 out drive lower gear casing

    i am currently experiencing a problem with the lower vertical shaft which slots into the lower gear casing. I need to know how far down the shaft sits as it should be sealing and preventing water from entering the lower oil res but alas it is not. The metal cylinder on the shaft doesnt seem to...
  20. B

    how to remove stuck stainless bolts from aluminium stern drive housing

    yep, got some pretty tight bolts here. Anyone got any ideas to free very tight or stuck bolts to avoid shearing? I have noticed some of the threads on the bolts seem to have corroded with the thread seating in the housing and this has bulked out the thread. Often the top half of the thread...
Top