Search results

  1. W

    2001 evinrude 135 ficht add fuel seperator

    i have a 2001 crestliner 1850 sportfish with a 135 ficht and a 8 hp yamaha kicker . i did some investigating and the only filter on it is the one that is mounted in the cowl of the 135 ficht . I have a 3 way valve to feed fuel to the kicker pre filter so the kicker is getting unfiltered fuel...
  2. W

    ficht vapor seperator oring part numbers

    For those of you who are having trouble with your vapor seperator such as sticking needle and seat . well you probably allready know that parts arent available you have to buy the whole pump vapor seperator combo for about $700 you can service your vapor seperator upon disassemble you will...
  3. W

    needed high pressure fuel pump for ficht

    I have a 2001 135 ficht i broke the top port off my fuel pump working on it .
  4. W

    ficht 135 2001 high pressure fuel pump

    I have read that there is a screen on the high pressure pump where is it and how do you clean it.
  5. W

    2001 ficht 135 running out of gas

    ok yesterday went out fishing boat ran perfect ran out there . switched over to kicker motor fished 4 hrs no problems yet. switched back to main engine ran in to channel no problems starting slow no wake in channel couple minutes later motor starts to idle rough spit an sputter i check primer...
  6. W

    Boat not revving past 4000 rpm

    I have a 2003 mercruiser 350 mag mpi Motor sems to be running fine but it wont rev past about 4000 rpm Boat used to max right out at 5000 rpm 43mph now 4000 rpm 34 mph It also seams to be lagging power the boat weights 5000 lbs and use to launch out of the water now it seams to be laboring...
  7. W

    need bravo 3 prop

    I need a bravo 3 prop complete assembly 26p
  8. W

    grease gimbal

    what zirk fitting is for greasing my gimbal bearing. I found all the ones on the outdrive outside of boat. but can only find 1 inside the boat. looks like it is the coupler i have greased. Alpha 1 gen 1
  9. W

    18' starcraft center console floor replacement

    I am getting ready to put a new floor in my uncles starcraft 18' center console nd i am looking for ideas. my questions are 1.do i need to tear out the old floor 2.Has anyone tried the recycled plastic decking that you use at home on your deck or something similar Any input would be helpful
  10. W

    5.7 mpi stuttering and no power

    2003 mercury mpi 555 ecm 350 mag. Here is the problem. I take boat out get it ready for season first day runs beautiful. Bring boat home decide to change my ex flappers {rattling}they are the old style 1 pc oval. y pipe is attached to an mr drive housing. Take boat back out another day wont...
  11. W

    mercruiser 5.7 mpi distributor help

    I have a 2003 mercruiser mpi with the 555 ecm.Somehow my distributor is broken where the cap screws down to the distributor the screw flange is broken off so i only have 1 screw holding my cap on. Here is my question since this distributor does nothing but supply power to my spark plugs in...
  12. W

    wood floor replacement

    I am replaing the floor in a 18 starcraft center console Alluminum boat. Should i use marine plywood or treated Do i coat with anything. going to put marine carpet in it
  13. W

    555 ecm 5.7 mpi

    would it be correct to say when you get a fault your 555 ecm stores it until cleard with a mercury scanner. I have a horn/fault message that wont go away . when i installed my smartcraft gauges i forgot the horn. I have now installed said horn but the message wont go away. Everything works...
  14. W

    Smartcraft alarm

    Last year i installed all new smartcraft gauges on my 350 mag mpi. Everything works great except i get a written alarm / horn when i turn on my key and My speedo that says alarm when cleared wont come back on until i turn the key off and back on. I need the audible buzzer or alarm that works...
  15. W

    Allumaloy ?????

    Does anyone have any experience useing Allumaloy or similar products. My crestliner has a few small leaks was wondering if this is the cure all it claims.
  16. W

    Rattle at idle

    I have an alpha 1 gen 1 coupled to a 350mag mpi. At idle not in gear i get a little rattle noise from the rear of the engine near the coupler. Is this normal i see a grease fitting on the coupler not sure if i greased this on install last year. I beleive the coupler is original 1989 came off 4...
  17. W

    Update on 350 mag overheating

    Ok here is my serial # OM360000 I put a bravo motor on a Alpha 1 gen 1 drive so i am overheating at idle speeds. I beleive its a 2003 (350 MAG MPI) 300 HP Here is what i found i need part #864327 orifice and 864353 o-ring Question these parts go in the tee below the thermostst housing do i...
  18. W

    High Thrust prop questions

    I have a 9.9 merc 4 stroke kicker on my 24' crestliner great lakes hardtop boat. currently i am useing the stock prop. when things begin to get a little breezy the kicker struggles to keep the boat on course since the wind is pushing the boat around typically i will have to turn and go with the...
  19. W

    mercury 9.9 to 15 hp conversion

    I have a mercury 1998 9.9 4 stroke can this be converted to a 15 hp i beleive they are both the same cc
  20. W

    mercury short to long shaft conversion

    I have a 1998 mercury 9.9 4 stroke i have heard there is a kit available to make this a 20" or 25" shaft
Top