Search results

  1. KillerKilgore

    '88 Johnson 15hp link 'n sync after cam throttle and carb top replacement

    J15ECCS w/ remote controls. Long story, short version. Need steps and advise after replacing the broken throttle cam, cam follower (w/roller), and top carburetor cover. The old carburetor top #331735. I'm replacing with #337833 because I already have it. But using the original slow speed...
  2. KillerKilgore

    RKL-24-L Proud daddy of twins. Maybe

    I just bought a set of matching 1962 Johnson 40HP outboards along with the power control box. Looks like they were stored in a barn for years. Rats scat and time has taken their toll on them. But they are not locked up. Wiring will all have to be replaced. Where should I start. I have a Seloc...
  3. KillerKilgore

    Kill switch Johnson J15ECCS

    Brother got a new to him (us) pontoon with a 1988 15hp Johnson electric start engine. Am able to start it via key switch but only way to stop engine is choke it or throttle all the way down in gear. Can't find where to attach a kill switch any body know. Thanks
  4. KillerKilgore

    1979 eska/sears 217.585831 set points

    This motor a 1979 7.5hp sears hasn't been started in over 2 years. Cleaned and THOUGHT I set the points right but it wants to kick back when it starts. Using 40:1 fuel mix. There was a triangle on the cam roller. I put the points arm just to the left of the cam roller is that right? But I found...
  5. KillerKilgore

    Sears/McCulloch 7.5 spurting out pee-hole/lots of questions

    I have a Sears (McCulloch) 7.5 electric start model number 574.60210. From what I can find it is from 1969. Should also be the same thing as a McCulloch 81635. Electric start does work but doesn't charge. Pretty sure it's a fuse issue. work on that later. Will also add rechargeable batteries in...
  6. KillerKilgore

    solenoid connections 62 evinrude 4 questions

    I have a 62 evinrude lark 6. It has a safety switch which should keep it from cranking with throttle is wide open. it does not. When the switch is engaged (idle to half throttle) the wire coming from the switch is showing ground. I tested it with multi-meter and have 0 ohm short to ground. When...
  7. KillerKilgore

    setting points on 62 40hp rude

    I just changed the points and plug wires on my rude and was just wanting to know where the throttle should be set. Was doing some research here and found this thread http://forums.iboats.com/showthread.php?t=294072 It did not mention where to set the throttle. Then found this thread...
  8. KillerKilgore

    HELP! JANE! Stop this crazy thing! 62 Erude Lark 6

    Need help think I know how to put a kill switch on this engine but not sure. Should I put wires from the points and when they make contact it will short out the ignition system and shut the engine off? (pic 1) Also have a few questions about the over rev cutout (pic 4) and what looks like a...
  9. KillerKilgore

    1962 evinrude lark 6 40hp no gen is this correct?

    New to me 62 40hp Evinrude Lark6 has not be started in about 10 years. Model 35028L (what does the L mean longshaft?) Acquired 2 manuals for 1.5 to 40 hp motors and they both mentioned a generator that should be on the motor but I find none. Is that right or did the PO remove it. I do not see...
  10. KillerKilgore

    Adjust Carb/Barrel empty

    Hello and thanks to all before I begin. I have a 1957 Johnson 10hp model no is QD-18. (found on forums searches) I have the motor running now after it was setting for God only knows how long. After cleaning the carb and new plugs. I know that the top needle is the slow speed adjustment (found...
Top