Search results

  1. A

    89 DT 55 overheat

    This motor overheated and wouldn't start or run well afterwords. the primary cause of the overheat was a clogged water intake. After inspection, the hard starting was caused by a bad choke solenoid.new water pump impeller and cooling lines are open. starts now and idles rough. Compression test...
  2. A

    new older merc

    Hi Folks, What can all of your combined knowledge tell me about a new in the bag Merc 70 HP motor serial number oc204983 <br />model number 1-0704129.<br />It was never installed and is in a gentlemans garage. these motors come with any hydraulics (tilt)? any idea what it would be worth ?<br...
  3. A

    oil fouled ?

    1992 Suzuki DT55.This motor keeps fouling plugs after being poorly winterized last fall.With new plugs it runs well for a few minutes then it seems to oil foul them. The carbs are spotless. I don't have the manual yet. sounds like an oil pump problem to me but i don't know how to test anything...
  4. A

    spark plug gap DT55

    While i wait for my manual to arrive(4-6 weeks from Suzuki dealer)Would anybody know the correct spark plug gap for a 1992 DT55. thanks.
  5. A

    DT 55 foul plugs

    Hi Folks,<br /> My friend got a DT55 last year. I believe it's a 1990 model. It ran great last year and he had a handy man winterize it last fall. This year it's a different story. It has fresh gas and fresh oil in the oil tank. the problem is that it fouls the plugs in about 10 minutes.Three...
  6. A

    plastic gas tank

    Hi Folks, I've read agreat deal on the use of plastic tanks and whether they become permanent tanks when they are over a certain capacity. I am now more confused than ever. I have just installed one 19 gal.plastic tank under the seat in my 17 foot Boston Whaler to replace the two 6 gal steel...
  7. A

    lower unit lube and shear pin

    on a 1953 7.5 hp Elgin the manual calls for waterproof grease to lube the lower unit. I just opened it up to inspect it and i guess the previous owner drained it before he stored it 20 years ago. The case and gears are oily but grease free and corrosion free and the gears look brand new. What...
  8. A

    a new acquisition

    my newest find is an Elgin Outboard model number 571.58761 serial number 761 10974 or at least that is what the original owners manual says on the front in pencil. The motor is currently moving at 65 MPH thru Ws. in the back of my sister's van on it's way to me. What year was this one made...
  9. A

    johnson AD 10 M ser. 1452476 year and decarb ?

    Hi Folks, I am working on the above described motor and it keeps fouling out the lower plug. what year is this motor ? The plugs my BIL installed are Autolite #303. They are supposed to be the modern equiv of what were originally used. True or false ? Would there be a better plug choice ? The...
  10. A

    remove KE 4 water jacket

    I'm trying to remove the water jackets on a Ke-4 and trying to avoid a complete teardown. I've unscrewed the four screws for the top cyl. and removed that water jacket . I removed the bottom 4 screws and the bottom water jacket seems to be held tight. i dont want to remove the cylinders and it...
  11. A

    sealing a water jacket

    In my 1949 Ke 4 manual it says to use "Permatex" to seal the water jacket gaskets. I haven't used that stuff in a long time and i remember it was really tough to remove that stuff. Is there a better and merc recommended product that i should be using or is Permatex still the required animal ?
  12. A

    removing flywheel

    on a 1949 KE4 7.5 hp i need to remove the flywheel. I have the tool for the flywheel nut. Any ideas on how to hold the flywheel from turning with out the flywheel holding tool ?
  13. A

    NAPA numbers

    Any body know what the NAPA part numbers are for points and condensers for a 1949 Mercury Ke-4 7.5 HP
  14. A

    1961 75 HP Temp Gauge ?

    Hi Folks,<br />Anyone how to install a temp gauge sender and gauge in this motor or if it is impossible to do ? If possible, what sender and gauge ? <br />Thanks in advance. Jerome
  15. A

    replace twin V-6 mercruisers

    Any body know how involved it would be and how much it would cost me to replace two V-6 mercruisers in a 1991 30 foot Carver. I'm looking at buying the boat. The guy who winterized it last year didn't pump any antifreeze thru the blocks and the motors are toast. all four manifolds are shot and...
  16. A

    oil ratio debate 1949 keikhaefer

    my project is a 7.5 hp motor that hasn't been run in a really long time.I've already done the water pump and rebuilt the carb,changed the lube and greased whatever needed greasing I stopped at a "Merc" dealer to pick up some two cycle oil and asked the service guy what ratio fuel oil mix i...
  17. A

    gamefisher 7.5 hp

    So then how does this water cooled leg idea work ? I didn't see the water outlet pipe connect to anything above the exhaust housing. Does it just run out of the pipe and dribble around the leg to cool it ?
  18. A

    gasket/washer

    on a 1949 keikhaefer ke-4 between the powerhead and exhaust housing theres a gasket and in addition to the gasket where the water supply goes into the power head there is a rubber washer.think i could use a washer made of gasket material instead of ordering a powerhead seal kit. the only rubber...
  19. A

    7.5hp 1949 kiehkaefer water pump serial 257445

    So the impeller was in pieces and i couldn't find but 3 of the impeller blades stuck in the water pump and housing. Yes i have the manual. The manual doesn't show all and i am curious if the finned piece on the port side, attached to the iron block between the cylinders and engine block which...
  20. A

    Kiekhaefer Rocket (long story)

    My newest acquisition is a Kiekhaefer Mercury Rocket,model KE 4, serial # 257445 in beautiful condition (appearance wise). The lady that gave it to me told me her husband bought it new and used it only a few times, but that every year he would service it, till a few years ago when he put it away...
Top