Search results

  1. H

    Coupler style shift mechanism or Cam style shift mechanism, on force 120 ?

    I have a 91 Force 120 and goofed by turning the shift shaft while changing the impeller. f/n/r still work but this seem a little off. I think I may have turned the shift shaft while doing so. Would this be a sign of a cam style mechanism.
  2. H

    Help with possible shift shaft issue.

    I took the lower unit off my 93 Force 120 to make sure I didn't have any clogs with the water cooling system. After putting the lower unit back on, I ran the motor with the muffs on. While testing the motor to make sure it would still go into gear, I can hear a clanking while going into...
  3. H

    Force 120, pumps water but overheat buzzer is going off

    Anybody else have this issue. I can lots of water pumping but the alarm went off. I shut down the motor and started it again and the buzzer stopped. A little while later, the buzzer went off again. Is it possible to overheat if you're pumping water.
  4. H

    Bilge pump will not shut off when float switch wire is attached.

    Is this possible due to a blown fuse, or is it most likely that the float switch is stuck.
  5. H

    Goofed big time, removed pivot screw when changing lower end oil. Help!

    Well I goofed big time. I think I removed the the pivot screw from the shift mechanism. Now when I put it into gear, forward or reverse, I hear a slight clank/grinding. How bad did I screw up and what can I do to fix it. I'm guessing I'm gonna have to take it to a mechanic and have the lower...
  6. H

    91 force 120 will not start

    So I changed the lower end gear oil today, put some fresh gas in and the engine starts cranking. Cranks like normal before starting, but it does not turn over. Try again and it barely will crank. The battery was charged. Buddy of mine thinks it might be a solenoid or voltage regulator. Any...
  7. H

    Maxum 1800XR interior needs new wood

    Hey guys, I have a 92 Maxum 1800XR that needs a little cosmetic interior work. On the starboard side by the rear seat, there is a vinyl covering over a piece of wood. The wood is rotted and coming apart. I would like to replace this. Is this something I will just have to take out and cut a...
  8. H

    Used Boat Checklist

    Hello everyone. I usually post the in the Force section as that's the outboard on my 92 Maxum 1800XR. But the urge to get something bigger has kind of bitten me. I have plenty of time to look as I'm not in a hurry and don't want to make the mistakes I made when I bought my first boat...
  9. H

    Loction on bilge pump on 1800 xr

    I have a 1992 Maxum 1800 XR with a Force 120 outboard. I was wondering if anyone knew where the bilge pump was located. I'm not having any issues with it but would like know in case of an emergency or future repairs.
  10. H

    Tilt/Trim won't raise lower

    Hey Guys, would appreciate any help you could give me. Got my engine running for the first time this year. Its a 1991 Force 120 Outboard. Only problem is that the tilt/trim motor is not getting power/running. I can hear a click in the relays but am lost. I was guessing maybe the pump motor...
  11. H

    Need new hydraulic valve body(PIC)

    Well I finally fixed all of my boats problems,(impeller and housing, complete trim cylinder replacement). While reattaching the hydraulic lines, one of the holes on the hydraulic valve body stripped. Anybody know a good source to find a replacement. This is the type I'm looking...
  12. H

    93 Force 120 Hydraulic line problems, Need Help Bad

    I had to disconnect my hydraulic lines from the tilt trim motor but forgot to photo or write down which lines went to which holes. On the bottom of my trim motor the holes are staggered with two on the left, and two on the right. The holes kind of look like this. X...
  13. H

    Impeller not turning, getting stuck in housing

    Ok I was on the lake and the overheat alarm went off. Shut it down quickly and got towed to the dock. Figured the impeller was dead. Took it home and submersed the lower unit in a tank and tried to run it. It started but water was not coming out the outlets. Changed the impeller, gaskets...
  14. H

    1993 Force Trim cylinder housing

    Hello, I'm new to the board and wanted to know if anyone knew a good source to find a cover assembly cap for the trim housing cylinder. I'll try to post a link, and it would be part #6 in the diagram. Any help would be great...
Top