Search results

  1. Bustedknuckle84

    Bf150 dtc 14 iacv troubleshooting, honda gurus help please??

    2019 honda bf150 with 70 hours. Trying to diagnosis an dtc 14 - iacv problem. Port Engine throws a code as soon as it starts, but runs. Sometimes it stalls as cranking, but once it gets running, idles fine, and no performance issues. Its only throwing code 14 when starting up. Before pulling...
  2. Bustedknuckle84

    Battery voltage drops when high amps needed for horn and halogen lights?

    2002 Cape Craft, with 03 Honda 200hp. I'm experiencing a recent issue where when I try to turn on my deck halogen lights, or use my horn for example the voltage is dropping significantly. The lights, radio, and stereo are on a different wire than the horn wire. Regardless, I have good batteries...
  3. Bustedknuckle84

    Low Pressure Fuel Pump Gas level when motor running question

    I have a 2003 Honda 200 hp fuel injected motor. Should the bowl containing the low pressure fuel filter always be full of gas?
  4. Bustedknuckle84

    Safe-t-Alert Gasoline detector installation area

    Bought a Safe-t-Alert Gasoline detector for safety reasons. Placing it in the outboard motor but should I place one under the boat deck too? Or is there not much of a risk of explosion under the deck when you have an outboard motor?
  5. Bustedknuckle84

    Gas odors with no gas leak help

    I have a 2002 Cape Craft 22cc its a center console with an 4stroke outboard and a 80 gallon plastic fuel tank. It also has a small walkin cabin for a porta potty and has drain. Whenever I take the boat traveling and even sometimes sitting the small walkin cabin will have to me a strong fuel...
  6. Bustedknuckle84

    HONDA TECHs please help fuel coming out of tube on frontside of engine?? Pic included

    I just re-cleaned on my water fuel separator and fuel pump. I did this before but this time have a weird problem when I put everything back. I turn the motor over runs GREAT now, however fuel is pouring out a tube connected to the front side of the motor. Pic included. Where does this tube...
  7. Bustedknuckle84

    Has anyone ever used a car fuel pump for their outboard High pressure pump?

    I have a few car pump laying around that still work. I have a 03 honda outboard 200 hp. I have a fuel pump from a 99 honda accord that was replaced due to an upgraded fuel pump. The pump seems to fit inside the High fuel pump housing quite fine except the top of the fuel pumps electrical...
  8. Bustedknuckle84

    Fuel System experts please help I have diagrams and pics

    I have a 2003 Honda 200hp but just need your experience with outboard fuel system. Trying to diagnosis a fuel problem. My Honda has a low pump #8 IN DIAGRAM (top of cylinder head cover) High Pressure pump(attached to the side of vapor separator). A few questions. 1) When high pressure pump...
  9. Bustedknuckle84

    Changing my user name?

    Hello mods, I would like to change my user name to a more boat appropriate one that will match my boats name. Who do I contact?
  10. Bustedknuckle84

    Does bad gas cause a NO firing or starting situation?

    Curious if a few months old gas could cause a no firing or starting problem?
  11. Bustedknuckle84

    BF200 Cranks but no start...

    2003 200 hp honda outboard. I know I have a fuel issue but can't figure out where the problem is. I have had the same fuel in the tank for a few months now and when I ran it last the motor died out. I thought it I ran out of gas so I bout some 100% gas to be able to run it again. Well the motor...
  12. Bustedknuckle84

    Kudos to Bennett Trim and TABMAN for a truly NO HASSLE experience!

    Had an issue with a port side trim tab actuator, sent the unit to Bennett Monday within 3 days I had a BRAND NEW Actuator at my door today. warranted out with no hassle! THANKS BENNETT I will post this in my local pensacola fishing forum and added you to my FB "likes"
  13. Bustedknuckle84

    Need advice using fence wood on boat please

    Im trying to move and raise my live bait bucket higher up (right now it sits on the deck). Im trying to use 2x4's (homedepot kind) and have it all cut out and planned. Should I paint the wood would or something to help prevent rot and mold from being outside? the wood will be below the bait...
  14. Bustedknuckle84

    wierd problem bennett trim tab stuck down need help

    I have the bennett sport tab i believe its the m80 model with the trim tab indicator with seperate controls for the trim tabs. The starboard side works fine the port side is stuck open. Heres what i have done so far. Cleaned all connections at helm and gound wire from the hpu to the battery...
  15. Bustedknuckle84

    Customer WOW Moment from greatlakesskipper.com like to share.

    Order a Tempress Boat hatch. Installed it very good construction and weatherproof which is what i was mainly looking for. So I ordered another one very good price too. The 2nd one had a pinched weather seal looked like a honest mistake. Contacted the Great Lakes Skipper and all I wanted was...
  16. Bustedknuckle84

    Voltage drop when halogen deck lights on and motor not running

    I have the main power wire going to a 4 way distribution thing that has the glass fuses.It distributes power to the radio,stereo, and halogen deck lights(one in the front one for the back). Problem: When I flip the switch for to turn on the deck lights the voltage drops to 8v's for the entire...
  17. Bustedknuckle84

    Top of the Gunwale foam options???

    Im just about done pulling and drying most of the old foam out. Looking to refill. Whats are some cost effective ways to refill with foam in the top of the gunwale where the rod holders go. Boat is listed below. Will the Great Stuff you get at lowes and home depot work?
  18. Bustedknuckle84

    Guest Charger hard wiring question

    Looking to hard wire an electrical plug to the charger wiring. Tried looking at the manual with no luck. Can someone tell me what color goes to what? hot,neutral,ground? My guesses? lets see how close i am lol. Blue= (neutral?) Green/Yellow=...
  19. Bustedknuckle84

    Any information on How to remove the top part of the boat (cap) from the bottom?

    Boat is in the signature. Just wondering what has to be removed to separate the bottom from the top of the boat to get into the hull. ex: does the motor have to come off? Any threads on this?
  20. Bustedknuckle84

    Gunwale Foam has water in it, very nervous about what to do! any advice please!

    Hull is a 2003 cape craft as described in the signature. I wanted to replace the seals around rod holders on the gunwale because the boat owner before me didnt know what he was doing. I pulled the rod holders our to see the top of the gunwales have foam but also has water in it. Very scared that...
Top