Search results

  1. limbwalker

    20’ Lund Alaskan bad attitude since going Etec

    Hello guys, I’ve owned my 20’ Lund Alaskan for over 10 years and that hull performed like a rock star with the original 320Lb 75hp Optimax Tiller. Ever since I’ve repowered with this new 390LB Etec 90HO Tiller, the hull rides absolutely terrible. I was running 3 blade SS on the Merc and now...
  2. limbwalker

    Strongest easiest Hull structural Rivet options

    Hello all, I picked up an older 14’ Springbok aluminum hull that’ll serve my intended fishing needs perfectly. Thing is the middle and front bench seats I’m wanting to remove them and relocate the more deep part way up the hull to give me more leg room towards the back. I removed the the top...
  3. limbwalker

    Mysterious Wiring 1984 Mercury 50

    Hello all, I?ve been helping a young friend getting his older 1984/85 (gold stripe) Merc 50 Going again after sitting for some time. I?ve rebuild carbs, new impeller, lower end oil, replaced choke solenoid, repaired a few broke out lower co areas with new fin silicone and small pop rivets to...
  4. limbwalker

    Wiring new Tachometer on 1998 Mercury 75 HP Optimax Tiller

    Sorry to start a bummer thread on something maybe as simple as a tach but when ya dont know well its best to ask the people that maybe do know.. I read a good starting place is the possibilty there might be 2 Grey wires running to the stator but thats the limit of what i have picked up thus...
  5. limbwalker

    Lowrance Elite 5 and Contour Lines

    Purchased a Elite 5 new about 4 yrs ago now and fishing at bottom end of Lake Huron at Head of the St Clair River, my IPhone with Navionics App shows all contour lines and yet my Elite 5 shows only 2. I know my Lowrance has a chip in it, just not sure which one it is. Friends of mine using...
  6. limbwalker

    Mercury Big Tiller

    Hello, first post here and hoping someone can shed some light on possible options to the Big Tiller Kits for my 98' 75hp Opti tiller. I'm into Handlining and trolling for walleye on the Great Lakes and seeing guys with the capabilities on their E Tecs with slowing their boats down with the +/-...
  7. limbwalker

    CDI Electronics website..

    I'm trying to find out and went to their site, yet still am not sure which single AC (unrectified) wire of the three to pick up and use to feed my isolator I want to run to charge my batteries..if someone could shed some power my way, I'd appreciate it...thank you
  8. limbwalker

    Which Stator Wire on 1998 75HP Mercury

    I'm trying to find out which owlud be the proper wire that produces around 15-17VAC from the stator as I need to pick it up and run it my Isolator i'm trying to get going in my old boat to charge onlu one aux battery ..I was informed that the isolators will not charge at a full 14VDC but if a...
  9. limbwalker

    Installing Powerline Isolators on Mercury 75HP

    I have a 1998 75 Mercury outboard, on a 20' Lund Alaskan, and bought a Powerline Model 33-10 Isolator for another old Starcraft I own and never got around to installing it, but now want to put it into this Lund..the Isolator has 3 posts on top A1, B1 and B2, ....Installation Instructions say to...
  10. limbwalker

    propping my 20' alaskan

    Hello all. I own a 20" Lund Alaskan with a 75hp Merc 2 stroke and last fall for duck hunting i purchased a 13 1/4" X 17" michigan SS Prop and which drove the hull perfect with the heavy loads I can put in it during hunting season..This past week I decided to go up another pitch to a 19" yet down...
  11. limbwalker

    Installing tach on 1998 Merc 75 hp

    Hello, I have a 1998 mercury 75 hp 2 stroke that I'd like to install a tach on it, and found out today from my dealer that they want $75 for the wire harness for it..If the Signal wire is gray, can I not just tap into it along with a ground wire to make it operate...then another wire to have the...
  12. limbwalker

    Missing ID Plate on 20' Lund Alaskan

    My late Father had purchased a Insurance claimed 20' Lund Alaskan in the late 90's that the transom and rear portion of port side had severe damage to and therfor removed the plate from the rear aluminum covering to remove transom . I have looked high and low for missing plate, but I wondered if...
Top