Search results

  1. A

    Transom rebuild Haines Hunter

    g'day all, Its been a while since my last post as my boat has been dry for 2 years with a rotten transom. Time to bite the bullet. Rot seems to be on top half and was going to try and dig down to good wood and do a partial replacement. Then put plate on rear for extra strength. Will be asking...
  2. A

    1988 V6 electrical engine connector.

    Gday, Im in process of removing outboard for transom inspection. My question is how this plug disconnects. It seems real tight and wondering if I just yank it straight off ? Also when pulling oil lines at motor do I need to open lid on reserve tank to release pressure ? thanks for any help. Paul
  3. A

    135 V6 outboard removal.Disconnect help.

    Gday all its been a while. Removing outboard for transom repair and need to disconnect wiring,fuel and oil lines and throttle / shift cables.Im guessing its best to disconnect all from motor side. Any advice on doing this the right way? When removing throttle and shift cables do I need to re...
  4. A

    Trim solenoid clicking up and down.

    Had this problem before and cleaned all solenoid connections.Worked for me last time,not this time.My question is if clicking at solenoid when using throttle remote switch,doesnt that mean switch is good and sending power?,...or will a dirty switch still send power to solenoid.?? Battery fully...
  5. A

    88 V6 Change Rectifier to Rectifier/Regulator.

    Gday all,Its been a while. My V6 only has rectifier and peaks at 17V at WOT.No problem with it as battery does the regulating,however im looking at new electronics that dont like over 15 -16 volts.Can anyone point me in right direction for a Rectifier/Regulator for my 1988 V6 135HP. Thanks Paul.
  6. A

    V6 135hp 1988 to 200hp Leg swap??

    Gday all,Got a crack on bottom of leg.Repaired a few times though still leaks water.Corrosion winning battle. Guy down street selling same year 200HP 88.Will his leg fit and work on my 135HP?? I know some 200hp have 2:1 ratio.
  7. A

    V6 135hp 1988 DVA test Coils...Cranking or Idle ??

    Gday All, Built a DVA a while ago and excited to test it out.Going to set my multimeter to 500vdc and want to test the coils output. My question is can i do this while engine is at idle or cranking only.I will be using a remote starter button to solenoid if it needs to be cranking only. Can I...
  8. A

    Jumping Solenoid with starter button..Key on or off ???

    Starting/cranking motor with home made starter button to solenoid.Did this last year but cant remember if ignition key needs to be in ON or OFF position. Also im sure its (Pos red to little red/yellow)to start.Correct me if im wrong. Thanks Paul.
  9. A

    Rust Converter on engine block??

    Got some chipped paint on bolt heads on engine block and mid section which have rusted a little.Could i paint with rust converter or normal paint better? Thanks Paul.
  10. A

    Battery Reading 17 volts at WOT.

    Gday all,Running a V6 Merc 88 model.Newish Marine battery working well.On fishfinder showing battery volt reading at around 12.8 with engine off.Running it shows increase volts to approx 13.5,but when near WOT yesterday it showed 17.0 volts.Is that too high or is it normal? Thanks for any help...
  11. A

    Installing 2nd Tilt/Trim switch.

    Im going to put back up toggle switch on dash as current switch playing up. Will it be OK if I just connect new wiring to Solenoids on top of existing wiring??Or can i only have one switch wiring connected to solenoid? Thanks for any help.
  12. A

    V6 135hp 1988 Getting hot at low RPM.

    Common problem,my V6 getting warm at low rpm and fine when I throttle up. Changed the impeller and going to check/replace Tstats and Poppet. While leg is off is there something else i can do.Should i flush water or air backwards through cooling system?Anyone know how to do this?Im thinking of...
  13. A

    Painting Gearhousing and Skeg question.

    Gday all from Aussieland. Just rebuilt water pump and base and decided to clean up mating surface to mid section as it was chipping/flaking.Ive cleaned it back to metal. 1.Should i prime first then paint with marine enamel,or just paint? 2.Can I do the same for the Skeg.
  14. A

    Impeller pump base V6.Confusion.

    Gday all. Pulled my water pump for service and decided to yank out the base as well.Have I pulled this thing apart in 2 pieces?Should i leave the blue disc shape seal in or try and get it out. Also as you can see ive cleaned up paint surface where it meets with mid section.anyone know if i...
  15. A

    V6 135hp 1988 Impeller change question.

    Gday all, Want to do an Impeller change and (Mercury) manual says have in nuetral when removing gear housing. Then when re- assembling,it says shift (gear housing)in forward gear and then to place (guide block anchor pin) into forward gear position.I have the EZ shift gear housing. Is this just...
  16. A

    V6 Tilt and Trim 3 Ram Question

    Gday all,looking at a trim system to buy online.Do all merc 3 Ram T&T systems from 80s - 90s handle V6s.This guy has a 3 ram and was told only 60 -90 HP??I thought 60 hp would be single ram only.Picture hard to see as all brackets attached including tilt tube etc.
  17. A

    V6 Tilt and Trim Rebuild.problem.

    G'day,Just rebuilt my 3 ram TnT unit.Main ram was completely disassembled and serviced.Put it all back together,filled and bled system.Main ram works great up and down no leaks.Problem is both trim rams not moving now.Unit still off boat.Does it need load on them to move????I've seen them on...
  18. A

    Tilt n Trim Corrosion advice.

    G'day all,Got my TnT off for rebuild and found some deep corrosion pits on base of unit(where Anode plate goes).dug at it with nail and some go around 6 ml deep (1/4 inch).looks like large grains of sand.My question is what type of steel is this as the corrosion is not brown like rust,just wet...
  19. A

    Can I clean inside Tilt Ram with Carb Cleaner??

    G'day all,When I eventually get the cap off tilt ram, I'm going to rebuild,seals,o ring etc.Manual says to clean with Parts Cleaner?? could I use Carb cleaner or should I just use a solvent(mineral Turps)then blow it out.
  20. A

    Now the Cross pin is Jammed on Tilt Ram

    Just took a week to remove seized transom Bracket for TnT pump removal and repair.Now I'm stuck with the cross pin at top of tilt ram.Punch and Hammer with heat,though still jammed.Any ideas/help greatly appreciated.88 V6 Merc.
Top