Search results

  1. L

    carburator adjustment

    hi, thanks for all the good advice. Just one more issue. How much do I turn the fuel air mixture screw on a 2 barrel mercarb on a 2000 3.0L merc engine. It has delco electronic ignition, thanks.
  2. L

    merc 3.0L tuneup

    Hi, could someone tell me what I need to do to give my 3.0L merc inboard ..outboard a complete tuneup. It is a 2000 carburated engine.
  3. L

    3.ol merc engine dripping water

    Hey everyone, just bought a 2000 bayliner with the 3.0l mercruiser. I have a little drip of water coming from the front of the engine when its running. Is it the water pump. Do I need to replace the whole pump or just a gasket or seal...Thanks
  4. L

    Shaft Length Issue

    I have a 14ft aluminum from Misty River. The transom measures 18 inches high from the very bottom to where the outboard clamps on. If I put a short shaft motor on then the cavitation plate will be 1 inch above the bottom of the boat because a short shaft motor measures 17 inches from the clamp...
  5. L

    cavitation plate height

    I have a 14ft aluminum and need to buy an outboard. The height of the transom measures 18.5 in. What length of shaft do I need. Should the cavitation plate be equal to the bottom, can it be a littlle below, cAN IT BE A LITTLE ABOVE...THANKS
  6. L

    longshaft or shortshaft?

    My 14 ft aluminum measures 18.5 inches from the bottom of boat to the top where the engine clamps on. I would like to purchase a new outboard. Do I buy a longshaft or short shaft?I thought a short is suppose to be 15in and a long 20. The motor that came off it measures 17.25in from the clamp to...
  7. L

    merc 170 starter issue

    Hey guys and gals, I am putting in a new starter on my 1986 170hp mercruiser and Im not sure how to connect the wires to the starter and solenoid. The starter that came out of it was not original and it did not have a solenoid on top and the new one does. The old one only had one power wire to...
  8. L

    170 merc electrical problem

    hey guys,my 170 merc i/o has no voltage at the coil when the ignition switch is on.Could it be a faulty ignition switch or is it something else.It starts and runs fine with just a little backfiring if you put the thrott down to fast.Any thoughts would be a big help.
  9. L

    propeller pitch delema

    hi, I have a 170hp merc inboard,outboard on a 19 ft regal sebring. It has a 14x19 three blade prop that revs out at 4600 rpm, which is right at the max for that engine.My question is this, if I want to put a four blade prop on ,would you go with a 14.5x18 or a 14.5 x20. Thanks
  10. L

    170hp mercruiser (help)

    hi, my 1986 170 merc backfires when I tried pulling a skier up the other day and feels like it is lacking power.Ive done a complete tuneup....new plugs,points,wires,timing,dwel,rotor,condesor,dist cap,even ran carb cleaner.Rus very well when warm ,idles nice, but backfires when you give it...
  11. L

    170hp merc...how high shoul it rev?

    hi, i have a 1986 170hp merc, just wondering what the maximum revs should be at full throttle, any ideas
  12. L

    shifting hard

    when i put it in forward it bangs into gear a little harder than i would like. it bangs a little harderwhen going into reverse. any thoughts
  13. L

    merc 170 carb trouble

    hi,my 170hp merc is rough on the start until completely warmed up,carb backfires once and awhile.Noticed it has one adjustment screw on the side of carb,and was wondering how to set it.tried just about everything else,complete tuneup but still runs rough and blows alot of black smoke but once...
  14. L

    170hp merc hesitation

    hi, i have an 1986 170 merc that the enigine hesitates only at full throttle, any ideas, thanks.
  15. L

    170 mercruiser engine troubles

    Hi, I have a 1986 170 hp merc inboard,outboard and have a little water getting in the oil.Was wondering what would be the most likely cause since I already replaced the head gasket
  16. L

    help with ignition

    I have a 170hp merc.two of the four spark plug wires accidently came off the distributor. How do I make sure I put them back on in the correct order on the distributor
  17. L

    170hp merc riser to manifold bolts

    Hi, could someone please tell me the proper pounds torque for the riser to exhaust manifold 4 bolts.It has an aluminum manifold
  18. L

    antifreeze in cylinder

    I have a merc170 and have coolant leaking into the no 4 cylinder.Just wondering if it is the head gasket but the old one looked fine when I pulled it apart.Also could it be the riser gasket where it bolts on to the exhaust manifold.It has an aluminum exhaust manifold.
  19. L

    marine battery

    hi, just wondering what the top 3 marine batteries would be
  20. L

    cooling system

    how to properly flush the coolong system on a 170hp merc with a closed system?
Top