Search results

  1. B

    force/chrysler lmb 229 walbro carb brass float new part number found

    part number that mercury has for this dosent fit..F10063 or 1395-8983 wont work...i have found that this carb body was on alot of other stuff..outdoor power equipment...part number that fits is 75-528-1 and it is brass...you can get it at most mower repair shops or walbro..
  2. B

    rewind starter new part number for spool for early force/chrysler

    was fa2459239..it is now 817811a-1 just got one from local marina for my montgomery wards/force/chrysler motor
  3. B

    15 hp montgomery wards cowl

    cant find it anywhere.is there any others that fit...btw its an 83 monkey wards
  4. B

    15 hp montgomery wards continuous running issue..update!

    i have a 15 hp 83 mont wards and it will start 2nd pull run really good for 5 min sometimes and then die..new fuel lines.. fuel pump working..while idling it will pop.... rev low then rev back up.... will idle only for a few min in neutral..same in if i run it in forward gear...fuel comes out...
  5. B

    52911d sea king monkey wards..timing how to set

    is it the same as jonhson evinrude? points set when point trigger is lined up with key way? on either side of course i know its .20
  6. B

    compression issue question

    i have a 74 6hp evinrude 6402c and i did comp test and got 80 psi on both cylinders is that low? what is factory?..will a seafoam and a head gasket get comp back up?
  7. B

    recommendations for new motor

    looking to get 15 to 18 hp 2 stroke,but which would your prefer looking for imput: mercury, johnson/evinrude?..mid 80s early 90s
  8. B

    74 e rude complete.

    finally done..motor sat for 11 yrs,..coils ,water pump ,carb rebuild ,rebuilt fuel pump.cheaper than buying new.. runs like a champ
  9. B

    74 6 hp e rude fuel pump repair kit

    do they make one for this motor?... found pin hole in diaphram....
  10. B

    white gas coming out of carb..pic

    as title states..it runs good 74 6 hp fisherman.pic is fuzzy but u can see it..caused by what?
  11. B

    weight of a 25 2 smoke evinrude 89

    wanted to know that info
  12. B

    74 6hp fisherman 6402c issue

    when i open twist to wot i still can open butterfly more at least 1/4 in....not running when i do this.also on the armature control the pin that goes in bottom broke on one side..will that effect anything..motor runs good just does seem to get to wot..coils plugs water pump carb redone..should i...
  13. B

    quick reply needed on prop hub question

    my rubber hub inside my prop turns alittle left or right when i put the shear pin and turn with pliers..bad hub?
  14. B

    weight of a 25 2 smoke evinrude 89

    wanted to know that info
  15. B

    problem here help

    i have a 74 6hp fisherman 12ft fbgls v hull..me and my girl and gear for fishing weigh maybe 450 lbs is this the motor to small for this setup?
  16. B

    which prop is better for my 6hp fisherman 74?

    8x7-1/4 or the 8-1/4x5 both 3 blade, the last one listed is for a 77 correct? would it be better on my 74?
  17. B

    74 6 hp fisherman spark plugs

    after running for 15- 20 min took plugs out and they are as clean as they can be..no oily residue..good sign?
  18. B

    74 6hp fisherman loss of power

    ok first of all i got this motor running thanks to evryone one on here,second i have a 12ft v hull fiberglass boat..when my girlfriend and i go out i give the motor full throttle and it seems to me that the revs are really low for full throttle,i like its at half throttle, went out by my self...
  19. B

    1969 johnson 1.5 hp carb question

    what are the adjustments? for this carb?
  20. B

    great info here..now a member!!

    thanks everyone for the info...ive learned alot here..got my 74 6hp evinrude running after my dad let it sit for 11 yrs..great little motor thanks again!!!
Top