Search results

  1. phillnjack2

    changing from mercury 15 spline to omc 13 spline on Ballistic prop ?

    Hi , I have a 13 1/8th x 21 ballistic propeller with the pressed in rubber hub. well I think its the old type of pressed in hub. I want to change this to omc 13 spline hub of the pressed in type. Now what I need to know is this, can I simply press out the original mercury and then press in the...
  2. phillnjack2

    Omc 56 cu in oval port service bulletins ?

    Does anyone know where i can get a copy of the OMC 56 cu in OVAL PORT service bulletins for the 1992 onwards 50, 60 and 70hp engines. I know there has been a good few bulletins and it would be nice to find out what they were/are . any info would be very nice .
  3. phillnjack2

    changing from 60hp to 70hp with larger carbs, question for the techs

    EVINRUDE 60HP YEAR 1995 MODEL NO E60TLEOC OVAL PORT 56 CU IN. cylinder compression with cold dry engine top 149 - middle 147- bottom149. At present I get 5900rpm with a 13x19 sst and max speed of just 42.3 mph. I make that a slip of just around 4%, that I think that is very good with a gear...
  4. phillnjack2

    Johnson 140hp 1977 wire identification. ?????

    hi guys, I am hoping someone can help us out with a electrical wire fitting .:facepalm: We are working on a friends 1977 Johnson 140hp model no 140ML77S. trying to get it all back up to a good running order and things are going fine so far. Now we have found a couple of wires that we just...
  5. phillnjack2

    commercial v recreational timing on 3 cylinder outboards ?

    do commercial outboards have different timing settings to normal recreational engines ? is this a way to de-tune outboard motors ? say on a 60hp 3 cylinder rude for example. my setting are 17 degree btdc for max advance timing. Would the same engine in commercial spec have the same timing or...
  6. phillnjack2

    How to dissengage fast start to check wide open timing on 1995 60hp triple

    1995 Evinrude 60hp Model no BE60TLEOC Hi guys I looked at the "joe reeves " way of checking the max advance/wide open throttle timing procedure. first thing he mentions is to disengage the quick start if you have this on your engine. well yes mine has this feature. but how do I disengage the...
  7. phillnjack2

    changing gear ratio's in a evinrude 3 cylinder 1995

    Ok first off I have the 1995 model 3 cylinder evinrude gear ratio is 2.42 to 1. the engine is longshaft with the newer multi spline main shaft from engine to gearbox and that will NOT be altered . I know some of the older model came with a 4 spline shaft,but this is the later version. My...
  8. phillnjack2

    fitting older carbs on a 96 evinrude ?

    Model no BE60TLEOC 1995 60hp evinrude 3 cylinder. Ok here is my question. what would be the problem (if any) of fitting a SET of1987 carburettors on a 1995 engine. The engine is a 60hp 3 cylinder 920cc or 56cu in how ever you want to look at it. the only difference between my engine and the...
  9. phillnjack2

    Timing at full throttle on the boat ??

    Evinrude 1995 60hp triple Model BE60TLEOC Ive seen it wrote down now loads of times about timing the engines at full throttle while running on the water. Now how on earth am i supposed to do that with a timing light while bouncing up and down in a 13ft boat ? i suppose ill have to make a...
  10. phillnjack2

    Will omc 433388 fuel pump be strong enough for a 1995 60hp rude

    1995 Evinrude 60hp triple Model no BE60TLEOC Hi folks i know the fuel pump is realy bad on my engine and it has to be completely replaced,parts repair kit is not good enough for this old pump. No way am i going to pay the prices wanted for repair kit just to use fuel side of the vro pump...
  11. phillnjack2

    lync and synce confusion , please help

    ok ive got a 1995 evinrude 60hp triple Model no BE60TLEOC Serial no G 03751787 im trying to get the carbs and timing syncronised, but i am comming up against a brick wall.:confused: this is what i read the throttle should start to advance the timing before the throttle opens the carbs or...
  12. phillnjack2

    Testing a vro fuel pump on fuel side only ? help please

    I have 2 vro fuel pumps, i dont know if any of them is good or bad, i wont be using the oil side for sure as i do know both of them are bad on the oil side. what is the best way to test the fuel side of these pumps to know if they are any good or not ? what sort of pressure does the pulse give...
  13. phillnjack2

    Evinrude 1995 60hp running terrible help needed

    Model no BE60TLEOC Serial no G 03751787 Year 1995 Ok here we go again :facepalm: The engine was running very nice, plenty of power nice idle, picking up very good but no more than 5700 revs. ok so the WOT revs are a bit low for a 13.5x 15inch pitch prop on a 13ft boat, but i could live...
  14. phillnjack2

    evinrude 60hp max revs 5700 ?

    engine is 1995 60hp triple model BE60TLEOC i have tried a few props now and my engine seems to be limited to 5700 rpm's i have been told by a few people that the limiter is somewhere between 6250 and 6750rpm. what could be the reson for me not being able to reach atleast 6,000rpm ? the boat...
  15. phillnjack2

    tohatsu 25hp prop ..what else will fit it?

    Hi guys A friend of mine has a 2 cylinder 25hp tohtsu that runs and purrs like a new engine. we know its getting on abit but its a real good little runner,just needs a decent prop on it. Now the problem is we have a prop on it thats on its last legs, and we want to know what else could fit...
  16. phillnjack2

    evinrude 1995 carbs sizes of 60hp and 70hp ????

    Evinrude 1995 3 cyl 60hp engine model BE60TLEOC Hello folks. My engine is the 1995 evinrude 3 cylinder 60hp triple. to look at its identical to the 70hp model and i need to know what is the actual difference in the carbs on these engines.:eek: The outer body even looks identical to mine...
  17. phillnjack2

    johnson 140hp 1977 coils !!

    engine model Johnson 140ML77S 140hp we are having a few problems with the coils on a friends 140hp johnson, year 1977. the coils have gone past their sell by date as the wires to them are breaking up and corroding. can i put coils from say a 1990's engine on this engine or is their going to...
  18. phillnjack2

    what RPM'S is the limit on the ignition of a 1995 60hp 3 cyl Rude

    The engine is 1995 Evinrude 3 Cylinder 60hp.(54ci) Model no BE60TLEOC Serial no G 03751787 Made in USA I need to know at what revs the limiter on the ignition comes in at ? ive been told by someone at brp its 7,000 rpm's is this correct ? or is it 6500rpms like someone else has told me...
  19. phillnjack2

    Tohatsu M25A2 propeller !!!!!!!!!!

    Hello folks my friend has a Tohatsu M25A2 with serial number 21881. we know this old girl is ancient (76 to 83) but it realy is a good reliable engine now we have coils replaced with a couple from a evinrude. The engine performs as good as new and is pretty good for a 25hp. The prop on the...
  20. phillnjack2

    Prop Guards ...what are the pro's and cons of fitting one of these ?

    Ok i have one of these bright red prop Guards it came with the engine when i bought it. it needed a couple of repairs and they have been taken care of. Now the promotion of these things leaves you thinking "it cant realy be that good" or can it ? The makers claim for these to improve handling...
Top