Search results

  1. monette999

    Not Permitted

    Sorry, not permitted in the forums. iBoats sells parts.
  2. monette999

    Dual Ignitron System Thunderbolt IV & MSD6 AL confirmation run on schematic

    Dear All, ​I would like to implement a Dual Ignitron System Thunderbolt IV & MSD6 AL on my boat. In case my OE System fails I have a backupsystem on board. For the ignition advance I have purchased a extra Thunderbolt Ignnition amplifier. I will have one OEM distributor and one cut out swich...
  3. monette999

    Dual Ignitron System Thunderbolt IV & MSD6 AL need advice

    Dear All, I would like to implement a Dual Ignitron System Thunderbolt IV & MSD6 AL on my boat. In case my OE System fails I have a backupsystem on board. for the ignition advance I have purchased a extra Thunderbolt Ignnition amplifier. I will have one dizzy and one cut out swich. Please let...
  4. monette999

    SeaRay 200 with SCB 350 (87-95). Edebrock Crosswind Intake 2604 or Std intake 2104

    Dear Forum, I have decided not to go with an marine intake. they are very expensive. A 2104 is about $130 USD & 2506 is $350. Hard Coating is $40 Dollar. Will use an std intake, but will alu hard eloxating the intake. This ensures always a nice outer finish. Using my boat only on fresh water...
  5. monette999

    Mercruiser Alpha One Thuderbolt IV need electical advise engine suddenly stopps

    Dear Forum, I am Bob quite new here and living in Germany. I am joining this forum since V8 boats & experts are hard to find here. After rebuilding my motor I was running my boat for a season without a proplem. Now it gives me some issues. It is stops running like somebody turns off the...
  6. monette999

    Mercruiser Alpha One Thuderbolt IV need electical advise engine suddenly stopps

    Dear Forum, I am Bob quite new here and living in Germany. I am joining this forum since V8 boats & experts are hard to find here. After rebuilding my motor I was running my boat for a season without a proplem. Now it gives me some issues. It is stops running like somebody turns of the...
  7. monette999

    Mercruiser V8 Fuel Pump: To place it here or to place it there that is the question?

    Dear All, ​since I had to replace my GM V8 I was missing the mechanical push-rod actuator to drive a mechanical fuel pump. So I thought use a Holley Red Line Fuel pump for carbs. 95gph. (my V8 has a single Rochester carb). OK I thought s mart and positioned the pump in the same place as the...
  8. monette999

    Engine Rateling after coupler & impeller change--- need good advise

    Dear Forum, I need some help. I have a 97 Searay 200 SBC 5.7L and changed my coupler. The replacement coupler came with 3 new bolts & 3 Triangle plates and no spring washers. So I took the old washers and assembled them. The new bolts had a type of washer integrated but it was not a spring...
  9. monette999

    Problem with Alignment of My V8 to Z-drive Alpha one Gen II

    Dear Forum, I have issues to correct align my Z-drive to my V8. I had to swap the Motor and as well put a new clutch into it. Now whatever position I adjust I am not getting the 3 Marks away from my alignmet tool, They are located always from 11.00 am to 1 pm. This is the best I can achieve...
  10. monette999

    Question about Mercruiser Coupler 18643A5

    Question about Mercruiser Coupler 18643A5 Hello I am writing you from Germany where my boat is and I would like your advice on my problem. I am a DIY guy and had an engine problem (305) last year on my 1994 Searay. I replaced the engine by a 350 SBC. Now on my fist boat tour on the Rhein I...
Top