Search results

  1. S

    97 yamaha won't stay running

    ok, I need some help with this issue. I have a 1097 yamaha wave venture 760. I got it 5 years ago and it has ran amazing from day 1. The last time I had them at the lake, it ran perfect. However for the last 2 years, it has sat on the trailer. So I am getting it ready to take out on the lake...
  2. S

    Building ramp need help

    I am planning to build some trailer ramps. I drive a semi truck, and am looking to hauling boats and vehicles in the enclosed trailer. The ramps will be 14' in length, but each ramp will be two 7' ramps connected together for a total of 14' and supported in the center by Jack's. The max weight...
  3. S

    boat seat frame

    I am in the process of rebuilding my interior of my larson open bow. I have designed how i want my seat to look and now i am picking the materials for the bench seat frame. Instead of using ply, i have played with the idea of using 2" thick foam pink sheet, wrapped in several layers of...
  4. S

    Reverse acting weird

    I have a 1984 Mercruiser 140 3.0L, connected to an Alpha MC1. I had the lower shift cable replaced by a marine shop. the outdrive fluid is full and water free. I had the boat out at the dock yesterday to test everything and I noticed something weird. When I shift into forward gear it goes in...
  5. S

    Gas smell

    Have a strange problem. I have a 1984 mercruiser 140 3.0L. Mercarb 2 bbl Carb. Manual fuel pump. I started the boat and ran it for a bit on the water muffs and the boat runs good. I noticed that if I let the boat sit for a while in the garage, when I go out to start it the next time, it takes...
  6. S

    Mercruiser 140 3.0L removal

    I am going to pull my motor today after work. It is a 1984 Mercruiser 3.0L, connected to an Alpha one. So far I have removed all the wiring, hoses, fuel lines, flywheel dust cover, and flywheel housing bolts. I am pulling the motor to replace the main oil seals, and install a new flywheel. My...
  7. S

    pre-power steering

    I have a 1894 mercruiser 3.0L. This is my first I/O boat. I took it out on the lake last weekend for the first time since I bought it and finished the rebuild. As I was driving it in a marina at idle speed it was fine. But then once I put the throttle down a bit I noticed the steering was VERY...
  8. S

    oil in bilge #2

    oil in bilge I took the boat out this morning for another test / tune run. The boat ran very well except for one issue that I noticed. I have a mud colored oil in my bilge bay. I can see where it slowly dripping out of. It is dripping out of the starboard side of the flywheel plate (circled in...
  9. S

    3.0L mercruiser running cool

    I have a 1984 Mercruiser 3.0L. I hooked it up to the garden hose today and tried to adjust the idle and mixture screw. It seemed that no matter what I did, it never ran right. once the choke warmed up and the plate was wide open it still was acting like it was getting too much air no matter...
  10. S

    mercruiser 3.0 Delco distributor tune-up

    I went to the marine shop yesterday and bought a new Sierra tuneup kit for my engine. It came with new points, condenser, and rotor. However in the kit there was also a little "pill capsule " with some black looking grease in there. I have not been able to find any reference to what that is used...
  11. S

    coil resistor

    I have a 1984 Mercruiser 3.0L with the Delco dist. The coil I had on there was a spare i had and the engine seemed to run fine. However i was walking through a "flee market" style warehouse the other day and saw a new coil in a napa box. The coil on the boat is old and dirty and I thought why...
  12. S

    Any guidance on how to change my shift cable? Thank you!

    Need help replacing shift cable. thanks Bt Doctor!
  13. S

    I think my Shifter is bad?

    I have a 1984 Larson with a 3.0L mercruiser engine. I have been battling a problem for almost 1 year now where my boat will shift into forward, but not reverse. If I tune the cable, I can get it to go into reverse but not forward. The other posts that I put on here over a year ago everyone was...
  14. S

    mercarb idle keeps changing.

    I took it down to the water today and while it was on the trailer I started the engine checked the dwell. Once the engine was running, the dwell was 24, so I made the adjustments and set the dwell at 31. I reset the timing to 6* BTDC. The engine actually ran much much much better while it was on...
  15. S

    Points dwell. need help

    OK so I finally bought a dwell meter. It is the actron dwell meter. I set the points with a .022 feeler gauge a while ago and thought that was close enough. My dwell meter has the 8cyl and 6 cyl setting so it says to multiply the 8 cyl reading by 2 for a 4 cyl engine. I hooked the green cable...
  16. S

    tested boat in water for first time. Need help.

    I just got done replacing my head gasket on my 1984 Mercruiser 3.0L engine. Today was the first time I have put my boat in the water since I bought it to test for leaks and see how the engine ran after fixing it up. On the trailer hooked up to the water muffs, I set the dwell to 32, set the idle...
  17. S

    what is tow weight?

    I am trying to understand exactly what tow weight means and how it is defined. my vehicle has a tow rating of 3500 lbs. Does this mean that I can tow a boat and trailer that weighs 3500 lbs. on a scale, or does this mean that I can tow something that requires 3500 lbs. of pull force to move...
  18. S

    blown head gasket. pictures.

    I did a compression test and the results indicated a blown head gasket. I removed the head and sure enough the seal between 2 and 3 was blown away. I am going to the marine store to get a new gasket. However while I had everything torn apart I wanted to make sure everything else was good. I am...
  19. S

    flywheel leaking. 3.0L merc...

    I have a leak on my engine that I discovered recently. This leaks when it is hooked up to the water muffs. It is not a bad leak, it is a steady drip give or take. There is oil in the bilge bay and I am not sure where this is coming from. The fuel pump was leaking oil around it, but I installed...
  20. S

    MCM 140 wiring help!!!

    I have been trying to figure out why my MCM140 is running rough at idle. So far this is what I have done. Set point gap to .022 with feeler gauge. new spark plugs set to .035" new condenser changed oil set timing to 6* BTDC took carb apart and cleaned it out 100%. set float drop to 27mm (1...
Top