Search results

  1. W

    OMC 3.0 cobra exhaust manifold change

    I've had high temperature issues since I bought this boat 3 years ago, it didn't run hot but it ran in the 180's or so. I changed the impeller, water pickup tube seals, water circulating pump. Then finally it overheated briefly and I removed the thermostat. It ran OK, but not great. But it...
  2. W

    removing lower gear case to service water intake tube.

    I think I have a leaky water intake, I bought the seals and I'm ready to separate the upper and lower. I also need to adjust my shift rod. Is there a gasket between upper and lower? Any tips on separating, I have removed the drive from the boat. Any tips on putting the two halves together again...
  3. W

    OMC 3.0 Cobra hit the bottom

    So I wasn't paying too much attention and I hit the bottom in shallow water. Dug up mud and the boat felt like it popped out of gear. After I realized what happened I got out of trouble in deeper water, and everything looked like it was working and shifting fine. It really took the paint off the...
  4. W

    anchor chock what to do with the rode.

    I want to mount the anchor on the bow of my boat to avoid storing it under my seat, and dragging it through the cabin area. I was thinking of something like this, my question is what to do with the rope (rode?). attach it to the bow rail? anyone have a setup like this? thanks.
  5. W

    cobra 3.0 winterizing after pulling the impeller

    I was extremely busy this fall and I was worried about a freeze up so I pulled the impeller, drained the block and manifold, pulled and drained all the hoses on my 1988 cobra 3.0. Well, now I want to start it up with the sta-bil ethanol treatment and fog the engine. Question. Do I need to hook...
  6. W

    over-reving omc 3.0 bayline capri 1950

    I bought the boat this year, it is a 1988 bayliner capri cuddy, 3.0 omc. It came with 2 props, a 4 blade and a 3 blade. I tried both, although the 3 blade is really beat up, the engine will rev to 5K or more If I hit WOT. The 4 blade is a 13.25 X 14 and the 3 blade is a 13.25 X 15. The holeshot...
  7. W

    Changed my shift cable, here is what I did. NOTE ** NEWBIE **

    I just bought the boat in March, I got it for cheap. It is a solid boat with very little or no rot, mechanically it ran great, didn't jump out of gear, and there were no nasty sounds coming from the engine or outdrive. BUT, it took a high effort to shift, and when I was on the water it didn't...
  8. W

    can't get my lower shift cable housing to unscrew.

    I'm at the pivot housing, and I can't get the cable housing brass nut to start turning to remove. Any tips? Heat. I soaked it with pb blaster. I', using a crowfoot, maybe I should just cut the housing and put a socket on there? TIA 3.0 cobra
  9. W

    automatic bilge pump indicator light

    I want to put an automatic bilge pump in my 19' capri cuddy. Either an attwood or rule, the type with the built in float switch. Is there a way of wiring in a light to indicate that the pump is running (drawing current)? I know I can do it with the separate switch pump type. TIA
  10. W

    will this allignment tool work?

    Ebay. CHeap, but will it work. Experts chime in. http://www.ebay.com/itm/Mercruiser-and-OMC-drive-alignment-tool-engine-align-/230524590568?_trksid=p4340.m503&_trkparms=algo%3DRIC.CFNP%26its%3DI%26itu%3DUA%26otn%3D5%26pmod%3D170817728861%26ps%3D63%26clkid%3D8121156902608633621
  11. W

    omc 3.0 cobra, gears work on muffs. hard to disengage forward on water.

    Started her up on muffs in the driveway. Shifts forward, reverse, very easy. Out on the water, put it in reverse to back away from the ramp. goes into forward just fine. drive around, engine is working great. When I stop I put the shifter in neutral and the engine idles but won't disengage. It...
  12. W

    Do I have an extra hose?

    At some point in my boats life, the previous owner must have tried a heater install. I found the heater core along with the auto fan (both disconnected, leaking I suspect). It looked like a clever idea, just executed a bit unorthodox. In any case, when looking at photos of other OMC 3.0 engines...
  13. W

    stainless bolts for thermostat housing. Good Idea?

    1988 3.0, OMC Cobra. I'm changing the Impeller and thermostat and I was wondering if it would be a good idea to go with stainless steel bolts for the thermostat housing. Or should I stick with the originals. I was worried about corrosion, but if they react with the housing and get stuck then...
  14. W

    3.0 omc running a temp

    I started it on muffs, and the water seems to be circulating good. Temp gauge went to 175 and I shut it off. If I feel the exhaust manifold it is cool to the touch, the water hose coming into the engine from the outdrive is cool (hose water), the hoses under the thermostat housing are very warm...
  15. W

    Any reason NOT to install a T in my water line coming from the outdrive to thermostat

    1988, cobra, 3.0. I want to have a sure way of flushing the engine and protect the impeller. I did try the muffs but I really didn't like them. Maybe I have more a philosophical issue than a real issue, I don't know. But I was wondering if I hooked up one of those prestone T flush kit into my...
  16. W

    manifold and block drain cocks...... stuck

    1988 omc, 3.0 . I tried to open the drain **** on my exhaust manifold and nothing. The little metal thing turned but no joy on the actual drain opening or closing. I also tried to just remove the whole fitting. I put a wrench on it but it didn't budge. I didn't put too much force on it, so it...
  17. W

    Windshield defroster?

    I bought this boat, and when I open the starboard rear seat, I found this. It is connected to 2 hoses that direct air around the engine, then into the box. The vents are in the bow facing portion of the engine bay, you can see the two flexible hoses in the engine picture. There is a smaller 1.5...
  18. W

    check shift cable OMC 3.0 cobra 1988?

    Is there a way of checking my shift cable for proper adjustment? Everything looks like it is working properly but before I hit the bay, I would like to make sure everything is in spec. Is the only way removing the outdrive and using the OMC adjusting tools? Would removing the cable from the...
  19. W

    2 battery setup

    I have a 1988 Bayliner capri 1952 cuddy, 3.0. It currently has one battery and I would like to go with a 2 battery setup with a switch. Question 1. I only have room to put the batteries on one side of the boat (the port side). Will this screw up my weight distribution? 2. Can I charge both...
  20. W

    Changing throttle cable on 88 OMC 3.0

    My throttle cable seems stiff, I looked at the cables on this site but I am unsure of the type of cable I need or the work involved. I have this control and this engine. Any help would be appreciated, thanks.
Top