Search results

  1. John2037

    Rocker oil flow on a 3.0? Is any flow good?

    My motor was rebuilt by someone else - had the cam gear slip and bang up one of the lifters. Now I repaired it, replaced all lifters and spun the motor around a few times to get oil flowing through the new lifters - adjust the rockers and test run. I don't know if there is a simple answer to...
  2. John2037

    Repairing my new 77 Johnson 115 - water tubes from the impeller housing destroyed....

    I've not seen this problem till now - It looks like someone had replaced the impeller and when putting the lower end on, instead of pushing it into place by hand, they used the mounting bolts and smashed the tubes up bad.... are these replaceable? They're copper so I guess I could just sweat in...
  3. John2037

    cam is too far in? lifter is hitting another lobe

    I am a pretty good mechanic but I have ran into more problems than I can shake a stick at with this 3.0 gm..... First machinist messed up the cut on the crank, second told me the head was good, seven valves later it was.... Now it sounded like another valve knock on #2 so I checked out the...
  4. John2037

    Xmas upgrade - what do you think trim tabs or a ss prop

    Hey guys, everyone says that ss props are more efficient and trim tabs make your boat more efficient, if you had to choose one what would you say? I have a really good deal on the trim tabs so to me its a very close cost. I have a fresh 3.0 Volvo penta with Cobra SX od that has a hydrofoil...
  5. John2037

    rebuilt motor breakin?

    Okay motor is almost completely rebuilt - went .20 over cylinder bore, .10 crank and flat top pistons. New cam, intake/exhaust manifold, riser, exhaust, flywheel, oil pump, oil pickup and rods. I had the head and block cleaned and machined true. I would say this motor is as close to new as I can...
  6. John2037

    flat top pistons okay? 3.0 181 rebuild

    Hey guys, the OEM pistons are dished and the master kit I just recieved came with flat pistons. I have always just replaced engine parts with the same parts, never really got into raising compression for HP or whatever.... Other than some timing/fuel adjustments -what are your thoughts on flat...
  7. John2037

    Replacing 3.0 motor, question for anyone whos replaced one

    Buying a new 3.0 to replace my older early model 3.0. Mine is a Volvo Penta 3.0 that has the two piece main seal, 12" flywheel hooked to a Cobra SX O.D. The new one has a 14" flywheel - Will this fit in the bellhousing and will my coupler work? One company says I have to get a modified...
  8. John2037

    Unknown electrical plug connector on the bow???

    Hey guys, I have a 98 Regal 1950 LSC and on the bow there is a multi-pin electrical connector, I can get a pic tomorrow @ storage but figured I'd ask now - maybe its a simple question. being a cuddy I can't imange it being a trolling motor connection (although where I boat that would be...
  9. John2037

    Any final tips or ideas before I replace this motor?

    I am a pretty good mechanic and I like to do the job right, the first time - this motor has stumped me! 1998 3.0 Volvo Penta GSMBY Penta Cobra SX OD Started with water in the oil - pulled the motor, discovered a mess of problems (bad riser, hacked exhaust smashed into the bellows, wrong fw)...
  10. John2037

    gps - chartplotter mounting location

    Hey guys, wondering if anyone knows what this feature is for or if anyone has mounted a gps/chartplotter here (there is a raised flat platform in front of the drivers window)? It seems like this spot would be more in the elements but it looks to be the best spot - what do you think?
  11. John2037

    Penta 3.0 interchangable top end parts?

    I need a head and intake/exhaust for a Volvo Penta 3.0 which are pricey but I see OMC and mercrusier parts all over for a lot less. From pics it looks all the same - GM block w/ a GM head (but with different names stamped in) and for the most part I found the intake/exhaust mani's all look the...
  12. John2037

    This cannot be right - gap behind motor to transom mount??

    I've gone through every diagram and exploded view out there but I haven't found exactly what I need - saw a good price on a 98 Regal 1950 LSC, seller seem trustworthy but his mechanic did THE WORST work I've ever seen! It's been quite a task getting the motor to where its at now (white silicone...
Top